Admiral Ice Maker Hardware

Your Price

$5.43

Admiral Ice Maker Screw

PartSelect Number PS11743743

Manufacturer Part Number WP681249

Sold individually.

Your Price

$13.20

Admiral Ice Maker Screw

PartSelect Number PS11742733

Manufacturer Part Number WP489128

This screw is sold individually.

Installation Instructions

Joseph from Baldwin, NY

dryer did not shut off no heat

took control pannel apart removed timer took new timer and replaced wire for wire the mounted new timer . removed old buzzer and replced wire for wire then mounted new buzzer screw was just in case I lost or stripped old one not needed . reassembled control pannel ,tested and found I needed more parts no heat so I opened the bottom and I ordered Igniter, sensor ,and thermostat and new coil kit . now i have heat but thermostat is back ordered timer works but not on regular auto dry but I do have heat ?? it has to be thermostat . now all the repair was relitivly easy but you had to watch and be carefull of what you were doing . when thermostat comes in I hope that will solve all the problems if not Read more...

Your Price

$7.44

Admiral Ice Maker Water Hose Clamp

PartSelect Number PS11742726

Manufacturer Part Number WP488878

This water hose clamp is used in your refrigerator to support the water tube. If the tubing or hose is working, but is loose inside the unit, the clamp, which is supposed to support it in place, could be broken or damaged. If this is a symptom of yours, you should replace the clamp. These tube clamps are sold individually, the screw is not included. Make sure to unplug your refrigerator from the power source before installing this part. Refer to the manual provided by the manufacturer for further instructions.

Fixes these symptoms

Leaking
See more...

Installation Instructions

Michael from Tucson, AZ

leak from back of refrigerator where water line enters ice compartment

replaced old water fill tube for ice maker because it would clog with frozen water which would result in leaking from back of refrigerator where water line for ice maker entered refrigerator. Parts arrived faster than anticipated from parts select. New part was made differently (up-graded) so that water would not freeze. removed old fill tube and replaced with new. replaced water tubing and secured. leak is no longer present and I do not anticipate further issues from this problem. Thanks Parts Select Read more...

Your Price

$13.49

Admiral Ice Maker Screw

PartSelect Number PS11745625

Manufacturer Part Number WP8281227

This screw is sold individually.

Your Price

$6.94

Admiral Ice Maker Water Tubing Clamp

★★★★★

1 Review

PartSelect Number PS11727816

Manufacturer Part Number W10833902

This water tubing clamp keeps the 3/16-inch diameter water tubing mounted to your refrigerator. Its purpose is to prevent shifting, kinking, or loosening of the tubing, ensuring a consistent water flow for the water dispenser and ice maker. It is typically located at the back of the cabinet near the inlet valve. If the clamp securing the tubing in your refrigerator is not properly secured, it can result in leaks or complete detachment. This poses a risk of water damage to your fridge, flooring, and nearby structures if not addressed promptly. To replace the clamp, refer to your user guide for its location. Then, use a screwdriver to remove the securing screw. Please note that this clamp is sourced directly from the original equipment manufacturer and does not include any additional hardware.

Your Price

$9.42

Admiral Ice Maker Retainer, Thermostat

PartSelect Number PS11740356

Manufacturer Part Number WP2315522

Your Price

$5.37

Admiral Ice Maker Compression Nut

PartSelect Number PS11740540

Manufacturer Part Number WP245183

Installation Instructions

Fernand from SOMERSET, MA

ice maker kept on dripping water causing ice in the icee containergood compression to freeze in a block

ordered a new shut-off valve. arrived in 5 days. installation had to wait a couple more day for i had to order a new compression nut. the reason i had to order a new nut was because the original nut was made of teflon and stripped easily when i tightened it to make a leak proof.joint. the new nut arrived in two days and was installed readily being that it was made of brass and consequently did not strip when i tightened to make a drip proof joint. finished in approximately twenty minutes' the video that this site has on the internet was of great value. Read more...