Amana Dishwasher Caps and Lids

Videos!

Your Price

$18.71

Amana Dishwasher Rinse Aid Cap

★★★★★

15 Reviews

PartSelect Number PS11755938

Manufacturer Part Number WPW10524919

This part holds the rinse aid liquid in the dispenser until the timer activates the rinse cycle.

Fixes these symptoms

Not cleaning dishes properly
See more...

Installation Instructions

Kathryn from WINTERPORT, ME

Rinse aid cap was melted when it came out of the designated spot and melted against the heat coil.

Open the washer door, remove old rinse aid cap. Place new cap into designated spot, screw into place. Read more...

Your Price

$15.52

Amana Dishwasher Tub Cap

★★★★★

1 Review

PartSelect Number PS11703426

Manufacturer Part Number W10795980

The plastic button covers the sharp ends of screws along the edge of the dishwasher tub. Sold individually.

Fixes these symptoms

Leaking
See more...

Installation Instructions

Royce from GREENSBORO, NC

Dish rack slide arms losing ball bearings

Unscrewed mounting screws, pulled dishwasher out halfway, replaced arms, 4 screws each side .....very simple 30 min tops. Parts perfect and quick delivery! Read more...

Videos!

Your Price

$11.12

Amana Dishwasher Rinse Aid Cap

★★★★★

14 Reviews

PartSelect Number PS11741341

Manufacturer Part Number WP3378134

This cap does not require the use of an O-ring seal. The wet agent assembly cap is clear in color and made of plastic. This is a part for your dishwasher. This part may need to be replaced if you notice that your dishwasher is not dispensing detergent, cleaning dishes properly, or has sprung a leak. The cap is found on the inside of your dishwasher door. This is an extremely simple repair that requires no tools. Simply open your dishwasher door, twist the old cap out of place, ensuring no pieces are left behind. Screw your new cap into place.

Fixes these symptoms

Leaking
Not cleaning dishes properly
Not drying dishes properly
See more...

Installation Instructions

Louis from Niceville, FL

Water dripped out from the bottom of door.

Diagnosing the problem, i.e. finding the source of the leak, was the hardest part. The best clue was the leak only occurred well into the cycle when the water was hot and steam was coming out the vent. I then assumed there was a bad seal and steam & condensed water was leaking down into the door. I replaced the vent duct & seal, a broken drip cover (an internal part in the door), and replaced a missing rinse aid cap. This stopped the leak. Read more...

Your Price

$23.53

Amana Dishwasher Dispenser Cap

★★★★★

6 Reviews

PartSelect Number PS11746156

Manufacturer Part Number WP8533380

This is the cap for your rinse aid dispenser.

Fixes these symptoms

Leaking
Not drying dishes properly
See more...

Installation Instructions

Brian from Marion, IA

Couldn't find the part anywhere, but...

PartSelect found the right part for me on the first try. I had scoured the web looking for this particular drying agent cap. Even Sears said I'd have to order the entire dispenser assembly - $$$!

PartSelect found just the cap I needed at a much better price.

Fantastic service. Shipping was faster than promised. I can't say enough good things about them! Read more...

Your Price

$39.73

Amana Dishwasher Rinse-Aid Dispenser Cap

★★★★★

3 Reviews

PartSelect Number PS11755940

Manufacturer Part Number WPW10524921

The rinse-aid dispenser cap is an original equipment manufacturer (OEM) part that fits Kenmore 665-series and Amana ADP1400-series dishwashers.

Installation Instructions

Mary Ann from AUSTIN, TX

Model number issue

When we ordered the part the first time, we pulled the model number from the documentation instead of the machine. We got the wrong part the first time. The people at Parts Select were very knowledgeable and helpful when we called. After we pulled the model number from the machine, they sent the perfect part that popped in with no problems. Read more...

Videos!

Your Price

$43.72

Amana Dishwasher Rinse Aid Cap - Gray

★★★★★

8 Reviews

PartSelect Number PS11755941

Manufacturer Part Number WPW10524922

This is the replacement rinse aid cap for your dishwasher. It is made of gray plastic and is approximately 2 inches in diameter. This rinse aid cap screws into the rinse aid assembly and prevents leaks. Sometimes the cap can become loose and fall out, which can cause it to be melted by the heater. If your cap is damaged or missing, this is the part you will need to replace it. This rinse cap is an authentic OEM part sourced directly from the manufacturer and is sold individually.

Videos!

Your Price

$81.58

Amana Dishwasher Protector

★★★★★

2 Reviews

PartSelect Number PS11746146

Manufacturer Part Number WP8531857

This part is used to cover the chopper blades.

Fixes these symptoms

Noisy
Not cleaning dishes properly
See more...

Installation Instructions

Patty from Caldwell, ID

Dishwasher leaving food residue on all dishes

Had to take apart dishwasher and replace chopper assembly. The dishwasher had a lot of debris in in including pieces of broken plastic forks. Now works great Read more...

Your Price

$7.60

Amana Dishwasher Door Vent Screen

PartSelect Number PS11741302

Manufacturer Part Number WP3371710

Fixes these symptoms

Leaking
See more...

Installation Instructions

mary from Fountain Green, UT

leaking water

The first thing I did was to investigate. I needed to find where the leak was coming from. It was leaking from just above tne door front panel, directly underneath the control panel buttons. I opened the dishwasher door, and decided to remove the door screen vent. I was covered with some offwhite fiberous, or filter like material. I thought perhaps the filter had broken down, and I ordered a new screen. When it arrived, and, although I had expected to receive a new filter with the plastic door screen, I didn't. There wasn't one to be ordered. I looked at the screen again. My problem was, that although I had considered that the substance I had thought was a filter, was instead build up of detergent, and other particals. That idea didn't seem to make sense. I didn't think it was possible for that stuff to get to the door screen. I thought, it was too far away from the dispenser and food particles. As it turned out, the buildup was, in fact, the problem. I properly cleaned the door vent, which was then fine, and I put it back into the door. There were no more leaks, that was it, and the problem was solved. As a last note however, unfortunatley, I have to return the new door vent screen that I ordered. I enjoyed solving the problem, and you all helped alot. Let's do it again sometime. Read more...