Frigidaire Washer Dryer Combo Switches

Videos!

Your Price

$128.15

Frigidaire Washer Dryer Combo Front Load Washer Door Lock and Switch Assembly

★★★★★

30 Reviews

PartSelect Number PS12364048

Manufacturer Part Number 131763256

This door lock and switch assembly is manufactured to lock the door on your front load washer to prevent it from opening while it is running. You may need to replace the door lock and switch if the door does not open or lock. Your washer will not start if the door does not lock. This part is also known as a washing machine door lock assembly. As per the manufacturer, some models require a new wire harness and a door strike for this door lock assembly to work on the appliance. The original style lock would require the door lock kit.

Fixes these symptoms

Leaking
Lid or door won’t close
Locking Issues
See more...

Installation Instructions

DOUG from KING FERRY, NY

Door on washer wouldn't lock or start

1. Unplug unit.
2. Unscrew 2 nuts holding top in place in rear of unit using phillips head screwdriver.
3.Slide top back and remove.
4. Open door of washer and unscrew 2 screws holding in door lock unit.
5.Pull out unit from the top and install new unit reconnecting the 3 wire connections. Read more...

Your Price

$82.69

Frigidaire Washer Dryer Combo Water Level Switch

PartSelect Number PS1146954

Manufacturer Part Number 134422700

Installation Instructions

Aaron from Williamson, WV

Leaking washing machine; water would not shut off on fill up and rinse

Replacing the switch is relatively easy, however, I would caution all experiencing similar problems one thing. Before assuming, as I did, that the switch was bad, first remove the panel of the washer that houses the washing tub/basin. On the back of the tub, check to make sure that the tube connecting the tub and switch has not come off from the tub as it did in my situation. The solution to my problem of a leaking washing machine where the water would not stop filling on both wash and rinse cycles was simply reattaching the tube to the tub. If I would have checked that first, total job completion time would have been under 15 minutes. Hope this helps. If you need to replace the actual switch, remove the knobs, screws, and panel. Remove the wires, tube, and screw from the switch and reassemble new switch. That took me about 30-45 minutes. Read more...

Your Price

$61.83

Frigidaire Washer Dryer Combo Start Switch

★★★★★

4 Reviews

PartSelect Number PS1146154

Manufacturer Part Number 134399700

This start switch is a manufacturer-approved replacement part for your dryer. A faulty start switch means your dryer will not begin its drying cycle. In order to complete this repair, you will need a Phillips screwdriver. Once you access the switch, disconnect the two wire leads and attach them to the new switch. Make sure to disconnect power to the unit before beginning this repair, and wear work gloves.

Fixes these symptoms

Will Not Start
See more...

Installation Instructions

Greg from Lampasas, TX

Knob craked and broke off the start switch

Removed all the knobs but the master washing machine control knob, then the control and cover panels by removing the two screws that held each one. Then removed the end plastic pieces to allow access to screws holding the switch onto control panel. Used pliers to pull wires off the old switch and put them back on new switch. Screwed it back in place and re-attached plastic end pieces. Re-attached the control panel, then the cover panel under the control panel. Read more...

Your Price

$15.63

Frigidaire Washer Dryer Combo Door Switch - 3 Wire

★★★★★

5 Reviews

PartSelect Number PS2330880

Manufacturer Part Number 134813601

This switch is for a dryer door with a drum light.

Installation Instructions

THOMAS from CROSS LANES, WV

drum light stayed on and the dryer would not run, "dr" was was displayed in read out

spoke with repair person he indicated problem was not door switch but control board, prior to repair person arriving I receive the switch in the mail, I unplugged drier used a small edged screw driver to remove door light switch, removed three wire clips from the old switch, re connected the wires to new switch pushed the new switch into its location, closed the door light went out and the drier started and has ran just fine ever since, saved myself several hundred dollars or a new drier Read more...