General Electric Dryer Belts
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular General Electric Dryer Belts
Your Price
$31.27
In Stock
General Electric Dryer Drum Belt
PartSelect Number PS11705916
Manufacturer Part Number 4400EL2001F
The belt wraps the length of the dryer drum, secured by a tension pulley and then loops around the motor pulley. If you find that the drum is not turning properly or at all while your dryer is in succession, it might be due to the belt being broken.
Fixes these symptoms
- Drum Not Spinning
- Noisy
- See more...
Installation Instructions
Arthur from SOUTHLAKE, TX
Noisy when drying. A bumping noise
Watched the video a couple of times. After that it was a breeze.
Read more...
Your Price
$31.89
In Stock
General Electric Dryer Drive Belt
PartSelect Number PS2350043
Manufacturer Part Number WE12X10014
This belt has a length of 87 inches, width of 1/4”, flat, with 4 ridges.
Fixes these symptoms
- Drum Not Spinning
- Noisy
- See more...
Installation Instructions
Michael from Warwick, RI
the rear drum bearing was worn the dryer became very noisy
i removed the scews just above thr opened dryer door, i was then able to swing the dryer top cover back. i then removed the lower front panel screws ,the the screws securing the front of the dryer ( where the door is ) and removed it. there are just 2 wires to disconnect. after the front is removed you gain full access for drum removal, remove the belt make sure the wires are not in the way and remove the drum.i also used a vacuume to clean the inside of the dryer. the front drum slides are very easy to replace only 2 screws each.remove old parts install new parts then just put the dryer back together in the reverse order i took it apart. after re-assembly i turned the dryer on it was so quiet running my wife and dogs were very happy. ps. i just want to thank the people at partselect for having all my parts in stock and for the speed in which i received them. other than having to repair my dryer it was a very pleasant experiance.
Read more...
Your Price
$19.81
In Stock
Your Price
$81.40
In Stock
General Electric Dryer Drum Belt
2. Removed the yellow clip screwed onto the top frame.
3. Removed the front frame of the dryer by unscrewing the two screws holding the front frame on – one on either side.
4. Mark w/ an (x) on same side of alignment for the 2 wiring connectors before separating them.
5. Removed the front panel by tilting it forward & lifted to unlatch it from the 2 clips at the bottom of dryer.
6. Unwound the belt encircling the drum by releasing the tension between the tensioner roller & drive pulley. (Its better to remove back access panel at this time & do this at the back since I found it necessary to do this anyway when re-installing the new belt).
7. W/ lifting motion, pulled the drum out from the plastic holder attached to the back of the dryer frame. Guided & completely removed the drum out of the dryer.
8. Unscrewed the 3 screws holding the old big bearing to the back of the drum.
8. Unscrewed the 2 screws & removed the plastic that had held the bearing at back of the frame.
8. Installed the new bearing by screwing it to the back of the drum with 3 screws. Be careful not to strip screws. Used help to hold new bearing in place & aligned w/ screws.
9. From the front, installed the plastic holder to the back of the frame by 2 screws and put the ball bearing in-between holder & the metal strip retainer coming from the back of dryer.
10. Used the grease that came with the kit on the plastic holder & the big bearing at the back of the drum.
11. Replaced w/ new belt then re-inserted the drum back into the body of the dryer frame, w/ lifting motion, re-inserted the bearing into the plastic holder.
12. Putting the belt into the drive & tension pulleys through the back access panel was easy but could be very hard to do if coming from the front.
13. Had to replace the front panel's top felt w/ glides that holds the drum at the front w/ a new one. Really important to pay attention to where the plastic glides excess portion is facing (towards front panel), otherwise the front panel might not fit when you snap it back to place.
14. Removed old felt remnants w/ blade scraper & sandpaper. Used adhesive that came w/ kit. Once tacky, put the new felt w/ glides on & used clamps to hold it in place.
15. Waited for 2 hrs. (watched a movie) then re-installed front panel. Make sure that the drum (front) lid rides on top of the plastic glides.
16. Latched bottom of front panel to the metal clips. Replace the 2 screws back into place holding the front panel.
17. Snapped the wiring connectors in place where the (x) marks align.
18. Lowered the top panel & snapped it back into place
Note: All parts came w/ fast delivery & OEM fit - very satisfied! Took my time & on every chance I cleaned & vacuumed all areas of lint & dirt since the dryer hasn't been serviced for more than 10 years... Read more...
PartSelect Number PS959964
Manufacturer Part Number WE12X10009
Used to turn the drum.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
Raul from Fountain, CO
Loud noise & clothes hanging in drum.
1. Remove power cord from wall outlet. Unlatched the top lid of the dryer by pushing a flat screwdriver under the R & L sides where a metal clip on each side holds the top down. 2. Removed the yellow clip screwed onto the top frame.
3. Removed the front frame of the dryer by unscrewing the two screws holding the front frame on – one on either side.
4. Mark w/ an (x) on same side of alignment for the 2 wiring connectors before separating them.
5. Removed the front panel by tilting it forward & lifted to unlatch it from the 2 clips at the bottom of dryer.
6. Unwound the belt encircling the drum by releasing the tension between the tensioner roller & drive pulley. (Its better to remove back access panel at this time & do this at the back since I found it necessary to do this anyway when re-installing the new belt).
7. W/ lifting motion, pulled the drum out from the plastic holder attached to the back of the dryer frame. Guided & completely removed the drum out of the dryer.
8. Unscrewed the 3 screws holding the old big bearing to the back of the drum.
8. Unscrewed the 2 screws & removed the plastic that had held the bearing at back of the frame.
8. Installed the new bearing by screwing it to the back of the drum with 3 screws. Be careful not to strip screws. Used help to hold new bearing in place & aligned w/ screws.
9. From the front, installed the plastic holder to the back of the frame by 2 screws and put the ball bearing in-between holder & the metal strip retainer coming from the back of dryer.
10. Used the grease that came with the kit on the plastic holder & the big bearing at the back of the drum.
11. Replaced w/ new belt then re-inserted the drum back into the body of the dryer frame, w/ lifting motion, re-inserted the bearing into the plastic holder.
12. Putting the belt into the drive & tension pulleys through the back access panel was easy but could be very hard to do if coming from the front.
13. Had to replace the front panel's top felt w/ glides that holds the drum at the front w/ a new one. Really important to pay attention to where the plastic glides excess portion is facing (towards front panel), otherwise the front panel might not fit when you snap it back to place.
14. Removed old felt remnants w/ blade scraper & sandpaper. Used adhesive that came w/ kit. Once tacky, put the new felt w/ glides on & used clamps to hold it in place.
15. Waited for 2 hrs. (watched a movie) then re-installed front panel. Make sure that the drum (front) lid rides on top of the plastic glides.
16. Latched bottom of front panel to the metal clips. Replace the 2 screws back into place holding the front panel.
17. Snapped the wiring connectors in place where the (x) marks align.
18. Lowered the top panel & snapped it back into place
Note: All parts came w/ fast delivery & OEM fit - very satisfied! Took my time & on every chance I cleaned & vacuumed all areas of lint & dirt since the dryer hasn't been serviced for more than 10 years... Read more...
Your Price
$39.16
In Stock
Your Price
$106.88
In Stock
Your Price
$98.70
In Stock
General Electric Dryer Drive Belt
??
Unplug dryer
Remove 4 screws behind touch panel
Tilt panel forward then up leaving wires attached
Rear has 2 screws on the rear ends facing down remove them at ends
Lift rear up then forward push and top will be freed (keep on top)
Front edges have 1 screw each but sharp areas watch
Open door and remove x 4 screws then lift up and forward bottom has tabs each end to hold in place
Wires for light and switch can stay attached, move front/door to side
Exposed will be the drum brace.. I changed the x 2 rollers while the drum brace was in place.
To undo the rollers you have to use a wrench to reach in as you use a nut driver to remove then re-install new roller with washer on inside and outside (pay attention when you remove)
Remove x 4 small screws..... hold drum inside then lift brace up and forward
Have assistance hold drum steady with pressure to the back otherwise you will have to align back to the rear rollers
Reach into the bottom for the idle pulley to remove drive belt tension... drive belt is VERY SKINNY and has ribbed side that faces the drum.
Reverse the steps.. Read more...
PartSelect Number PS959966
Manufacturer Part Number WE12X10011
This part is used to rotate the drum.
Installation Instructions
Philip from FREEHOLD, NJ
Noise and Squeaking from Front During Drying
Front roller bearings were bad and figured to do the belt while in there. I bought the manual online which was very helpful.??
Unplug dryer
Remove 4 screws behind touch panel
Tilt panel forward then up leaving wires attached
Rear has 2 screws on the rear ends facing down remove them at ends
Lift rear up then forward push and top will be freed (keep on top)
Front edges have 1 screw each but sharp areas watch
Open door and remove x 4 screws then lift up and forward bottom has tabs each end to hold in place
Wires for light and switch can stay attached, move front/door to side
Exposed will be the drum brace.. I changed the x 2 rollers while the drum brace was in place.
To undo the rollers you have to use a wrench to reach in as you use a nut driver to remove then re-install new roller with washer on inside and outside (pay attention when you remove)
Remove x 4 small screws..... hold drum inside then lift brace up and forward
Have assistance hold drum steady with pressure to the back otherwise you will have to align back to the rear rollers
Reach into the bottom for the idle pulley to remove drive belt tension... drive belt is VERY SKINNY and has ribbed side that faces the drum.
Reverse the steps.. Read more...
Your Price
$17.84
Special Order
Related General Electric Dryer Parts
- All General Electric Dryer parts
- General Electric Dryer Bearings
- General Electric Dryer Brackets and Flanges
- General Electric Dryer Caps and Lids
- General Electric Dryer Circuit Boards and Touch Pads
- General Electric Dryer Drums and Tubs
- General Electric Dryer Elements and Burners
- General Electric Dryer Filters
- General Electric Dryer Handles
- General Electric Dryer Hardware
- General Electric Dryer Knobs
- General Electric Dryer Latches
- General Electric Dryer Legs and Feet
- General Electric Dryer Motors
- General Electric Dryer Panels
- General Electric Dryer Seals and Gaskets
- General Electric Dryer Sensors
- General Electric Dryer Switches
- General Electric Dryer Thermostats
- General Electric Dryer Timers
- General Electric Dryer Valves
- General Electric Dryer Wheels and Rollers
