Hotpoint Dishwasher Springs and Shock Absorbers

Videos!

Your Price

$9.19

Hotpoint Dishwasher Recess Door Spring

★★★★★

12 Reviews

PartSelect Number PS285013

Manufacturer Part Number WR02X10585

This door recess spring or dispenser lever spring in your refrigerator is used to return the ice door to the closed position or the dispenser lever to the home position once released. You will find the spring in the water dispenser assembly, behind the main control panel. If the dispenser lever is malfunctioning or the dispenser ice door is not closing, you may need to replace this door recess spring.

Fixes these symptoms

Door latch failure
Door Sweating
Door won’t open or close
See more...

Installation Instructions

Bill from Cleveland Heights, OH

flap to ice dispenser would not close

The flap to the ice dispenser would not close, which allowed the ice dispenser to frost up, freezing the water dispenser.

This was a simple fix. The solenoid had stopped working, so it would not automatically close the door flap. I read some posts on this site that suggest that you had to remove the trim around the entire dispenser to get at the solenoid. My fridge may be a newer model, but in any event it was much easier than that. Just below the touch pad for choosing water, ice, or crushed ice (above where the ice/water dispenses) there are three very small holes spaced about an inch a part. After unplugging the fridge, I stuck a small philips-head screw driver in each, freeing spring clips. That allowed the touch pad to come off. I then removed four screws to remove a plastic piece covering the chute, giving me access to the flap and solenoid. I just unplugged the solenoid from the circuit board on the back of the touch pad and then removed three screws to remove the old solenoid. I replaced it with the new solenoid and plugged it into the circuit board. The touch pad then snapped back into place.

The hardest part was figuring out how to get at the solenoid. After I found that pushing the clips in those three holes allowed me to remove the touch pad, it could not be any easier. Read more...

Your Price

$10.23

Hotpoint Dishwasher SPRING DOOR

PartSelect Number PS11700869

Manufacturer Part Number WD03X20445

Your Price

$11.44

Hotpoint Dishwasher Spring Plunger

PartSelect Number PS1019010

Manufacturer Part Number WD03X10026

This is a replacement spring plunger for your dishwasher. The spring is approximately 1 inch in length and is sold individually. The spring plunger helps your door latch correctly, and if the spring is missing or damaged, you can experience a door latch failure, and your dishwasher may not start. This is an OEM part sourced directly from the manufacturer.

Fixes these symptoms

Door latch failure
Will Not Start
See more...

Installation Instructions

MICHAEL from ORLEANS, IN

would not start

First I removed the 6 screws that hold the inside cover on the door.Then I remover the plastic cover over the switches,pulled out the switches and disconnected the 2 wires from each switch and connected connected them to the new switches exactly as they were on the old switches.Then reinstalled the switches in their holders.I then removed the plunger and spring from between the switches and installed the new spring and plunger exactly like the old one was installed.I reinstalled the door cover making sure everything was in it's place,I put the screws in the door cover and I was done.It was a very simple job. Mike Read more...

Your Price

$36.85

Hotpoint Dishwasher Detergent Cup Door Spring

PartSelect Number PS263846

Manufacturer Part Number WD3X764

Fixes these symptoms

Door latch failure
Will not dispense detergent
See more...

Installation Instructions

Joe from Waxhaw, NC

Detergent Dispenser Door Would Not Stay Closed

Completely remove the door from the dishwasher - It's easier to work on this way.

First the spring tension is NOT that critical - the spring just needs to not be mangled and really out of shape. Unless someone has taken a pair of pliers to it, it should be o-k
to use. I even mangled up the slot in the lever with a pair of pliers to try and jeery-rig it and it still works fine - you MUST at least have some resemblance of a groove here for the spring to
catch.
1) hook the hook on the inside of the lever where the slanted groove is on the cam. (see your great diagram)

Put all the pieces together at this point, shaft,spring and lever

2) There are two sets of grooves that correspond to matching notches in both the lever and the dispenser shaft. Make sure these match up to one another.
3) Using a pair of hemostats or tiny pliers pull the other side of the spring clockwise - gently - until you can hook it on the stop that is on the inside door. There will be some
tension of the spring around the shaft to cause the hook to engage to the slot in the plastic lever.

[*]This is where MOST of my problems were at:

4) Test the dispenser door to make sure when you close it, it springs back up. It WILL NOT hold when the door is off.
[*][I was trying to get the dispenser door to stay shut while the door was removed from the washer - this will NOT happen]
5) If number four is happening above, attach the door to the dishwasher.

Very Important: The door will only stay closed when the dishwasher is in the OFF position. Otherwise it will spring open when you try to shut it, because it is suppose to because at this time
in the cycle the detergent would be dispensing - hence the door being OPEN and the door not latching. Read more...