Jenn-Air Ice Maker Hardware

Your Price

$5.43

Jenn-Air Ice Maker Screw

PartSelect Number PS11743743

Manufacturer Part Number WP681249

Sold individually.

Your Price

$7.97

Jenn-Air Ice Maker Screw - 10-16 x 1

★★★★★

2 Reviews

PartSelect Number PS11741409

Manufacturer Part Number WP3387230

This screw is sold individually.

Installation Instructions

Wendy from BRAINTREE, MA

Freezer handle came loose on one side

Discovered that the seating in the handle was stripped on one side so removed the old handle (toughest part of the repair). Based on a previously asked/answered question, the PartSelect website provided an accurate list of the required parts (and corresponding part numbers) so I had everything I needed. Installing the new handle was very straightforward and quick. Read more...

Your Price

$8.06

Jenn-Air Ice Maker Screw

★★★★★

5 Reviews

PartSelect Number PS11738704

Manufacturer Part Number WP179051

Sold individually. Lock washers are used with screws when vibration from an appliance may cause the screw to loosen. Lock washers are also used in the electrical components of an appliance to ensure an electrical connection is not lost.

Installation Instructions

donna from baltimore, MD

missing screws for oven door

After searching on the internet for a very long time, we were almost ready to order the screws "blind" (no picture) from Sears for almost $10.oo per screw. Then I stumbled onto this website and found exactly what I was looking for, with a detailed description AND a picture!! Not to mention a price that was two thirds less than Sears..for TWO screws. Now the oven door is secure and we are no longer on our search for the right screws. Read more...

Your Price

$7.93

Jenn-Air Ice Maker Screw

★★★★★

1 Review

PartSelect Number PS11742721

Manufacturer Part Number WP488729

Metallic screw that is less than an inch long. Does not include the plastic washer.

Installation Instructions

Kyle from Wimauma, FL

Black Cam was bren on lower door hinge

This was a very simple job. Remove the top Hinge bracket, a total of 4 screws, lifted the door off the bottom hinge, removed the bottom hinge set up, 2 screws, replaced it, and attached the new bottom black door cam, lifted the door back onto the bottom hinge and aligned the top hinge, and reinserted the screws, and Ta Da, The door works like a new refrigerator door. 15 to 30 min tops. I did not even have to take the refrigerator items out of there door holder. Read more...

Your Price

$8.06

Jenn-Air Ice Maker Screw

★★★★★

1 Review

PartSelect Number PS11740977

Manufacturer Part Number WP3196163

This screw is sold individually.

Your Price

$11.12

Jenn-Air Ice Maker Screw

★★★★★

1 Review

PartSelect Number PS11745622

Manufacturer Part Number WP8281196

Sold individually.

Installation Instructions

Carol from Monroe, NY

Refrig making a lot of noise

The motor kit had only two wires coming out of it. The existing one in the refrig had 6. I spliced the 2 red to one black on the new part and 2 white to the other black wire on the new part. The two green I attached to a screw. I left the 6 wire harness in place just cut off the plug piece that went into the old motor, and spliced all my wires.
Worked great! Read more...

Your Price

$7.97

Jenn-Air Ice Maker Screw - 8-18 x 5/8

★★★★★

1 Review

PartSelect Number PS11747050

Manufacturer Part Number WP9741232

Sold individually.

Installation Instructions

Charles from Brooklyn, NY

Water leaking out under door

The pump outlet gasket was sticking out and a screw was missing from the pump outlet housing. This was causing water to flood out under the door.

Once I removed the pump outlet housing I saw that the gasket was out of place almost all the way around. I cleaned around the housing, replaced the gasket and the missing screw.

You need a Torx T-15 for this repair. Note that all of the screws on the housing were loose so you might need to tighten them from time to time.

Be careful not to drip a screw when you are installing it since it's a real hassle to fish it out from under the screen.

Once everything was tightened up, the wash pressure seemed to be much higher. Read more...

Your Price

$7.77

Jenn-Air Ice Maker Screw

★★★★★

2 Reviews

PartSelect Number PS11747542

Manufacturer Part Number WP98165

This screw is a little under an inch long and is made of metal. It is used with a refrigerator's ice maker assembly. Sold individually.

Installation Instructions

Lynn H from MILL CREEK, WA

Hinge pin for drawer lid broke

1. Remove all drawers {3}, shelves {glass 1}, shelf support {1}. 2. Remove two {2} screws from End Cap. 3. Carefully remove End Cap and drawer temperature control part on the back wall keeping them aligned as installed. The part on the back wall swings out so that the tab on the left end of the piece may be withdrawn from the securing slot (hole). The two parts should be carefully removed while keeping the two parts at a right angle the way they are installed. The reason for this caution follows. 4. On the back side of both parts are plastic pieces that, I believe, can be easily broken if you are not aware. The pieces are connected together at the right angle. They are the control arms for the temperature control -- on right side End Cap only -- the left side doesn't have them or the rear part on the back wall. 5. The pieces must be disconnected and removed. You must examine and ponder how they are held in place and hooked together in order to disconnect and remove them without damaging them. The same advice is applicable to reinstalling the pieces in the new part -- End Cap. 6. After reassembled and keeping the two parts at a right angle, insert the tab on the left end of the back wall part into the slot (hole) and swing the two parts back into position. 7. Replace the screws. 8. Done, reinstall the shelf, shelf support, and the drawers. NOTE: I ordered the two screws but they were not needed. Read more...

Your Price

$5.43

Jenn-Air Ice Maker Single Hex Head Screw

PartSelect Number PS11742731

Manufacturer Part Number WP489069

Sold individually. The size of this screw is 1/4" hex head and 10-12 x 1/2".

Installation Instructions

Chris from Pompano Beach, FL

Water in bottom of dishwasher

Disconnected power. Shut off water supply. Took off the front, disconnected copper supply line and flexible water line, removed water inlet valve. Took elbow from old inlet valve and put in on new one. Put new valve in, reconnected water lines, put back front panel. Opened water supply, Flipped breaker back on. Done and it worked! Read more...