Maytag Washer Belts

Find Your Part

Model number locator Need help finding your model number?
  • Search your model number to find:
  • Genuine OEM parts guaranteed to fit
  • Free manuals and guides
  • Repair instructions and videos
Maytag Appliance Parts
Shop By Part Type

Popular Maytag Washer Belts

Videos!
Your Price
$41.25
  In Stock
Maytag Washer Belt Kit
★★★★★
★★★★★
71 Reviews
PartSelect Number PS2005284
Manufacturer Part Number 12112425
This kit includes both the drive belt and the pump belt which are both V-shaped. If your washer does not toss, spin, or drain water properly, this might be because one of these belts has worn or stretched out. This results in the belt losing its grip and no longer driving the pump. The pump belt is black and made of rubber. The pump belt is located between the motor and pump underneath the washer. Simply remove the belt and hook the new one around the pulley. You may need to loosen or tighten the belt to ensure it is set in place properly.
Fixes these symptoms
Installation Instructions
Charles from Whitman, MA
Drum would not drain and there was a banging noise when the drum spun
I removed the 2 phillips screws on the bottom of the front panel. Then checked around to find the belts were actually below the floor panel.
I pulled the washing machine away from the wall and tilted it bacwards and found the pump belt was off the pully and the drive belt was badly damaged. I replaced the 2 belts which took no tools and about 3 minutes to accomplish then resecured the front panel, pushed back in place and leveled. Complete repair from diagnosis to back in operation took less than 15 minutes. Read more...
Videos!
Your Price
$19.71
  In Stock
Maytag Washer Drive Belt
★★★★★
★★★★★
20 Reviews
PartSelect Number PS11747978
Manufacturer Part Number WPW10006384
The main drive belt is designed to ride on the pulley until the basket gets up to speed.
Fixes these symptoms
  • Burning smell
  • Spinning Issues
  • Spins slowly
  • See more...
Installation Instructions
Jerry from WALLA WALLA, WA
Noise on bottom of Washer louder as time went on. 1 1/2 years
Well, first investigated and found loose nut on drive clutch. First take off the two screws with nut drive then cover off using a screwdriver blade to snap off the cover. Then socket ratchet to take off the nut on drive clutch. take off belt by slowly rotating the drive gear. two screws that hold the electronics to the upper drive clutch and put aside, so you can snap off the cover for drive clutch on upper part with screwdriver and off the parts come and install whole unit back as took it apart. Line up the new upper clutch so that is position as was before. (Using parts diagram helps a lot as www. partsselect.com has for you or Maytag.com.) Then put the electronic part board back on and the gear and nut. Make sure it is tight by several attempts to make sure it's snugged up good and then slowly roll belt back on the pulley and motor drive. Put your cover guard back on with two screws and done. Read more...
Videos!
Your Price
$10.98
  In Stock
Maytag Washer Drive Belt - 51 inches long
★★★★★
★★★★★
25 Reviews
PartSelect Number PS11738882
Manufacturer Part Number WP21352320
This V-style drive belt measures 51 inches long and 3/8 inches wide. The belt is made to slip on the motor pulley to bring the basket up to the speed required. Continued use can result in the belt suffering from wear and tear. Replace the V-style drive belt if you notice that it looks damaged. The most common symptoms of a damaged drive belt include: a burning smell or a loud grinding noise coming from the washer; the drum will not spin, spins slowly, or will not agitate; the washer shakes and moves, will not start, or will not drain.
Fixes these symptoms
Installation Instructions
Ranse from Layton, UT
Pump was making a grinding noise
The pump is located behind a small panel on the back, lower left side of my washer. It's attached to the bottom frame with 3 screws. It has two hoses attached, each with one spring clamp. Lift one side of the washer and slip the drive belt off the pully. Release the spring clamps on the hoses with a pair of pliers and remove the hoses. A small amount of water will drain from the hoses and pump when removed. Remove the three screws holding the pump to the frame and remove the pump. Install the new pump in the same position. Reattach the hoses, replace the belt, and reinstall the cover panel. That's all there is to it. Read more...
Videos!
Your Price
$37.77
  In Stock
Maytag Washer Drive Belt - 52 inches long
★★★★★
★★★★★
15 Reviews
PartSelect Number PS11739438
Manufacturer Part Number WP22003483
This washing machine drive belt is used with some clothes washers. This belt is all black in color and is made entirely of rubber.
Fixes these symptoms
Installation Instructions
James from Hueytown, AL
Washer tub would not spin, pump would empty water from tub.
Lay washer on front, removed belt. Removed center pulley with thrust bearing (pulley was worn on upper end, against thrust bearing, thrust bearing was worn also). Installed new thrust bearing & pulley kit. Cleaned & lubed slots that motor insulators slide in, installed new belt. Read more...
Videos!
Your Price
$40.58
  In Stock
Maytag Washer Drive Belt and Motor Isolator Kit
★★★★★
★★★★★
8 Reviews
PartSelect Number PS2003327
Manufacturer Part Number 12001788
This kit contains a flat drive belt, two motor isolators, and an instructions sheet. The drive belt is made to slip on the pulley until the basket gets up the desired speed.
Fixes these symptoms
  • Burning smell
  • Spins slowly
  • Will not agitate
  • See more...
Installation Instructions
richard from austin, MN
Drains but doesn't spin, door lock does not engage.
Door locked light did not come on and did not have 120 VAC across the Wax Motor. Also the Wax Motor did not extend out to make contact with the Door Lock, Spin Enable Switch. General guidance is to replace drive belt and to replace Wax Motor along with the Door Lock, Spin Enable Switches (total of two limit switches). This did not correct the problem. Checked for power and traced loss of power back to the Control Board where resistor R11 was found to be burnt out. Replaced Resistor with new Carbon Film unit, rating of 3.9 K-ohms, 1/4 W and 5%. As a prcaution, replace the Triac (manufactue part number NTE5657), component identified as Q6, rating of 0.8 Amp, 600 VAC. Semiconductor parts must be obtained from somewhere other than Parts Select (unable to find in the small town I live in, I located on the internet at Mouser.com). Unit works great now. Read more...
Videos!
Your Price
$52.85
  In Stock
Maytag Washer Drive Belt
★★★★★
★★★★★
12 Reviews
PartSelect Number PS11754067
Manufacturer Part Number WPW10388414
This drive belt is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear. NOTE: Per Manufacture, belt measures 48.22" long uninstalled and the belt will stretch To 51.53" when installed.
Fixes these symptoms
  • Burning smell
  • Spins slowly
  • Will not agitate
  • See more...
Installation Instructions
Francis from Rochester, NY
Washer made loud banging noise during spin cycle
I first removed the back panel held on by about 10 screws. I removed the drive belt from the pulley, then removed the lock nut securing the pulley to the drum & removed the pulley. Attached the new pulley to the drum, tightened on the lock nut, attached the new belt & ran a spin cycle. When that went OK I replaced the back panel & the washer was back in service. Read more...
Your Price
$67.36
  In Stock
Maytag Washer V-Style Spin and Agitate Belt - 28-3/4 inches long
★★★★★
★★★★★
3 Reviews
PartSelect Number PS11740577
Manufacturer Part Number WP27001006
This v-style spin and agitate belt is 28-3/4 inches long and half of an inch wide. It is all black in color and made entirely of rubber.
Fixes these symptoms
  • Burning smell
  • Spins slowly
  • Will not agitate
  • See more...
Installation Instructions
Ralph from Moreno Valley, CA
unusually loud rumbling in spin mode, no spin out
removed outer enclosure to expose inside workings. removed all retaining springs to tub and transmission housing. Inverted tub to access agitator pulley and belt. Removed pulley and cut belt off.(I knew I was replacing it, anyway.)Had to remove large tub bracket to exchange new pulley for old. Disconnect bleach reservoir filler tubing on tub assembly. Disconnect power connector to drive motor. Removed water pump to access drive pulley where new belt belongs. Aligned belt to pulleys and checked idler pulley tension which was acceptable. Replace helix drive lug against spin/agitator and tightened retaining bolt. Assembled components in reverse order and conducted test run. Success. Smooth running machine and saved about $200 on professional labor costs. I had no repair manual but you should have a personal confidence in general repair work. Something like a history of taking things apart and putting them back together successfully. I had an independent appliance repair guy examine the washer and he said it was too complicated for him. Once I had it apart, it seemed fairly basic. Good luck! Read more...
Your Price
$45.97
  In Stock
Maytag Washer Belt
★★★★★
★★★★★
1 Review
PartSelect Number PS11751386
Manufacturer Part Number WPW10260319
Your Price
$84.20
  In Stock
Maytag Washer Spin Belt
★★★★★
★★★★★
5 Reviews
PartSelect Number PS11740578
Manufacturer Part Number WP27001007
This v-shaped spin belt helps transfer power from the motor to the transmission to help pump the water in and out of the washer. It also helps runs the spin cycle in the washer.
Fixes these symptoms
Installation Instructions
Bruce from Medina, OH
Belt wore out
Had to remove pump-not easy. Nothing wrong with pump, but had to trash it to get it off the motor shaft, so I had to replace it, too.

Pop up top of cabinet and remove front panel. (I leaned unit back against a wall to facilitate internal access once panel was removed.)


Remove motor assy - 4 screws & connector.

Remove 3 pump screws (torx) and 2 hoses. Pry pump off motor shaft (not easy). I used a heat gun to help expand the plastic fitting on the motor shaft.

Remove old belt, put on new belt. (Do not use automotive belt-this belt is designed to slip because it also spins the tub. The tub will not spin when it's full of water, and the pump will not pump the water if the tub is bogging down the pump. Plus, you will probably overheat the motor.)

Press new pump back on motor shaft (advise not to re-use old pump as seals were probably damaged by removal process.)

Caution: Pressing pump onto motor shaft may cause pump rotor to bind in housing. Try to press it on a little too far so you back off slightly.

Replace pump screws.

Replace motor, giving attention to belt alignment.

Replace motor screws and connector.

Re-attach hoses on pump.

Button up cabinet.

Done.

The hardest part was removing the pump. If not for that, it would have been a 15-min, $20 repair.

Because I felt it wise to replace the pump also, it was a $70 repair. Read more...
Your Price
$60.51
  In Stock
Maytag Washer Drive Belt
★★★★★
★★★★★
5 Reviews
PartSelect Number PS11754068
Manufacturer Part Number WPW10388418
The main drive belt is designed to ride on the pulley until the basket gets up to speed.
Fixes these symptoms
Installation Instructions
Robert from OAKDALE, CT
Replace worn washer belt
Remove old belt, rotate large washer belt wheel, guiding belt off large wheel.
Guide new belt onto Washer Large Wheel. Use a pair of pliers to hold belt onto wheel as one turns the large washer belt wheel, guiding belt onto wheel. Note belt will be tight. Seems like belt will not fix but keep going it will fit, you might even hear it pop on.
Old Part number (W10116215) new replacement Part number (W10388418).
New replacement washer belt fits tight, that is ok. Read more...

Related Maytag Washer Parts

Back to Top