Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
Models
>
11020112310
11020112310 Kenmore Washer - Overview
Sections of the 11020112310
[Viewing 6 of 6]Keep searches simple, eg. "belt" or "pump".
Seal, Inner Cap
PartSelect #: PS11748108
Manufacturer #: WPW10072840
This is an inner cap seal, but may also be known as an O-ring, and it is a part for your washing machine. Some symptoms replacing this part will fix include: leaking from your appliance, uncontrollabl...
$11.12
In Stock
Lid Latch Assembly
PartSelect #: PS3497627
Manufacturer #: W10404050
The point of the lid switch is for the tub to stop spinning when the washer lid is opened. It is a safety precaution just in case someone decides to stick their hand inside the washer while the tub is spinning.
$47.93
In Stock
Agitator Cap Barrier with Seal
PartSelect #: PS11748113
Manufacturer #: WPW10074580
The O-Ring is included with this cap. It can be purchased separately as Part #WPW10072840.
$11.12
In Stock
Washer Drive Pulley
PartSelect #: PS10057144
Manufacturer #: W10721967
This is a replacement clutch assembly or cam kit for your washer. The clutch assembly is mounted on the drive shaft on the bottom of your washer. You may need to replace the clutch assembly if the spl...
$54.48
In Stock
Drive Belt
PartSelect #: PS11747978
Manufacturer #: WPW10006384
The main drive belt is designed to ride on the pulley until the basket gets up to speed.
$19.75
In Stock
Washer
PartSelect #: PS11742027
Manufacturer #: WP3949550
This part goes on the agitator retaining bolt.
$7.70
In Stock
Suspension Rod Kit
PartSelect #: PS11703288
Manufacturer #: W10780045
This knob is a genuine OEM replacement part used in dryers. It is a white, plastic knob found on the front panel on the dryer. It allows users to choose the drying cycle, adjust temperature settings, ...
$82.39
In Stock
Shift Actuator - 120V 60Hz
PartSelect #: PS11747977
Manufacturer #: WPW10006355
This part changes the transmission from agitation to spin mode. This actuator is for washers.
Actuator shifts the splutch and monitors the position of the splutch.
$73.54
In Stock
Lid Latch Strike
PartSelect #: PS11750882
Manufacturer #: WPW10240513
This part is the replacement lid latch or latch assembly for your top-load washer. The lid latch holds your washer door closed, and allows the washer to run its cycle. If the lid latch is damaged, you...
$44.48
In Stock
Hose Clamp
PartSelect #: PS11740613
Manufacturer #: WP285655
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
$11.12
In Stock
Lid Hinge Mounting Screw
PartSelect #: PS11748588
Manufacturer #: WPW10119828
Sold individually. NOTE: The color on the screw may not be the same as the image, but will still function the same.
$11.80
In Stock
Lid Bumper
PartSelect #: PS11747040
Manufacturer #: WP9724509
This gray and white washer lid bumper contains a rubber bottom and is sold individually.
$7.97
In Stock
Questions And Answers for 11020112310
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Shawn
August 30, 2023
The washer shakes like you would not believe during spin cycle
For model number 11020112310
Hi Shawn, thank you for your inquiry. We have concluded that the issue is with the suspension rods kit, part number PS11703288. Suspension rod kit supports the wash tub and keeps it stable during unbalanced loads. We hope this information is useful!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
- < Prev
- 1
- Next >
Common Symptoms of the 11020112310
[Viewing 12 of 12]Will not agitate
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Lid or door won’t close
Fixed by
these parts
these parts
Show All
Spins slowly
Fixed by
these parts
these parts
Show All
Burning smell
Fixed by
these parts
these parts
Show All
Spinning Issues
Fixed by
these parts
these parts
Show All
Shaking and Moving
Fixed by
these parts
these parts
Show All
Does not dispense fabric softener or detergent
Fixed by
these parts
these parts
Show All
Locking Issues
Fixed by
these parts
these parts
Show All
Marks left on clothes
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Lid Lock light blinking, machine will not start
A detailed Service Technician Service Manual is hidden inside the machine on the front panel. It is hidden by the bleach dispenser input. It gives a list of fault codes and instructions for calibration after repair, resetting fault codes, and a manual test mode for stepping the machine through each mode on command. The Tachometer faile
... Read more
d which would not let the machine come up to maximum spin speed. The tachometer is part of the solenoid actuator that shifts the transmission. It is not specifically called out in the manual. Any failure causes the lid lock light to blink which gives the appearance of a lid lock failure
Read less
Parts Used:
-
David from Los Alamos, NM
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
312 of 388 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Defective lid latch - Cabrio Washer
The instructions that came with the part were worthless. Essentially, unplug, put in new part, plug it back in. I spent a considerable amount of time on the internet and finally found a video showing how to open the top. Unlike other models, it is held down by clamps in the back rather than clips in the front. Once finding this inform
... Read more
ation the installation was simple. Remove the clamps and the back of the console, slide the top forward and lift, remove and replace the lock and reassemble. You don't even have to remove the hoses.
Read less
Parts Used:
-
William from Wakefield, RI
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
93 of 112 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Noise on bottom of Washer louder as time went on. 1 1/2 years
Well, first investigated and found loose nut on drive clutch. First take off the two screws with nut drive then cover off using a screwdriver blade to snap off the cover. Then socket ratchet to take off the nut on drive clutch. take off belt by slowly rotating the drive gear. two screws that hold the electronics to the upper drive clutch
... Read more
and put aside, so you can snap off the cover for drive clutch on upper part with screwdriver and off the parts come and install whole unit back as took it apart. Line up the new upper clutch so that is position as was before. (Using parts diagram helps a lot as www. partsselect.com has for you or Maytag.com.) Then put the electronic part board back on and the gear and nut. Make sure it is tight by several attempts to make sure it's snugged up good and then slowly roll belt back on the pulley and motor drive. Put your cover guard back on with two screws and done.
Read less
Parts Used:
-
Jerry from WALLA WALLA, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers, Socket set
83 of 112 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!