The point of the lid switch is for the tub to stop spinning when the washer lid is opened. It is a safety precaution just in case someone decides to stick their hand inside the washer while the tub is spinning.
This drive hub kit (part number W10528947VP) is for washers.
Drive hub kit W10528947VP connects the spin basket to the spin shaft that spins the basket. The kit may include multiple parts; refer to...
This is a replacement clutch assembly or cam kit for your washer. The clutch assembly is mounted on the drive shaft on the bottom of your washer. You may need to replace the clutch assembly if the spl...
These parts are the replacement suspension rod supports for your washer. They are made of plastic and are approximately 1 ½ inches in diameter. This package will come with an 8-piece set of suspension...
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
This part changes the transmission from agitation to spin mode. This actuator is for washers.
Actuator shifts the splutch and monitors the position of the splutch.
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
This insert is sold individually. Knob not included. Knob is sold separately.
$11.12
In Stock
Questions And Answers for 11021302013
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
9 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Linda
November 7, 2019
We replaced the lid lock but did not fix the problem of the lid lock light either starting to flash, or goes off and stays off after the wash cycle finishes, and will not agitate or spin for the rinse cycle.
For model number 11021302013
Hello Linda, thank you for your question. It sounds like the issue could be with the Shift Actuator - 120V 60Hz Part Number: WPW10006355. We would recommend replacing that part. I hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Fonn
November 8, 2023
I need a timer switch for Kenmore washer but can’t find one.
For model number 11021302013
Hi Fonn, thank you for reaching out. According to our research, your model comes with the control board, part number PS3653305, instead of a timer. The control board manages the washer's functions such as filling, washing, draining and spinning. We hope this information is useful!
Hello Roy, Thank you for your inquiry. We show the capacity of this model as 3.2 cubic feet. We hope this helps and if you need a part or advise in the future, please do not hesitate to contact us.
Was this helpful?
Thank you for voting!
Don
May 28, 2023
Machine won’t start up
For model number 11021302013
Hi Don, thank you for reaching out. We have researched and found the issue is most probably related to the lid latch assembly, part number PS3497627. Before replacing it, we advise checking for a tripped circuit breaker and a power cord that might be damaged. We hope this sorts out your problem!
A detailed Service Technician Service Manual is hidden inside the machine on the front panel. It is hidden by the bleach dispenser input. It gives a list of fault codes and instructions for calibration after repair, resetting fault codes, and a manual test mode for stepping the machine through each mode on command. The Tachometer faile
... Read mored which would not let the machine come up to maximum spin speed. The tachometer is part of the solenoid actuator that shifts the transmission. It is not specifically called out in the manual. Any failure causes the lid lock light to blink which gives the appearance of a lid lock failure
The instructions that came with the part were worthless. Essentially, unplug, put in new part, plug it back in. I spent a considerable amount of time on the internet and finally found a video showing how to open the top. Unlike other models, it is held down by clamps in the back rather than clips in the front. Once finding this inform
... Read moreation the installation was simple. Remove the clamps and the back of the console, slide the top forward and lift, remove and replace the lock and reassemble. You don't even have to remove the hoses.
Well, first investigated and found loose nut on drive clutch. First take off the two screws with nut drive then cover off using a screwdriver blade to snap off the cover. Then socket ratchet to take off the nut on drive clutch. take off belt by slowly rotating the drive gear. two screws that hold the electronics to the upper drive clutch
... Read moreand put aside, so you can snap off the cover for drive clutch on upper part with screwdriver and off the parts come and install whole unit back as took it apart. Line up the new upper clutch so that is position as was before. (Using parts diagram helps a lot as www. partsselect.com has for you or Maytag.com.) Then put the electronic part board back on and the gear and nut. Make sure it is tight by several attempts to make sure it's snugged up good and then slowly roll belt back on the pulley and motor drive. Put your cover guard back on with two screws and done.