The timer knob clip on your washing machine connects the timer knob to the control panel. If your timer knob is damaged or will not stay in place, you may need to replace the clip. If the timer does n...
$11.02
In Stock
Order within the next 9 hrs and your part ships today!
This V-shaped drive belt is 29 1/2 inches long x 1/2-inch-wide, and fits both front-load and top-load washing machines. When belts are worn or frayed, they are known to make noise. If you have a top-l...
$14.13
In Stock
Order within the next 9 hrs and your part ships today!
This part is the replacement timer knob for your washer. It is made of white plastic and is about 1 ¼ inches in diameter. The timer knob sits on the timer shaft and allows you to choose the wash cycle...
This is a water hose clamp kit for a variety of appliances including dishwashers and washers. This is a genuine replacement part. The kit includes two hose clamps. The smaller of the two is 1 inch in ...
$15.92
In Stock
Order within the next 9 hrs and your part ships today!
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
1 question answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Louise
July 4, 2022
Could you please tell me how old this machine is, it’s a Beaumark
Model #54140119 it’s a top loader I know it’s pretty old just wondering if we would still get parts for it?
Thanks
For model number 54140119
Hello Louise, Thank you for your inquiry. The age of an appliance is actually contained within the serial number. If you could resubmit your inquiry with both the model and the serial number we would be happy to look up the age of the unit for you. We do show that we carry a few parts for this model, so if there is a particular part you are looking for, please let us know and we would be happy to check and see if we carry it. We look forward to hearing from you.
Used the spatula to release the front panel (push flat spatula under top about 2 inches from either side to release the two sprng clips holding the front panel on) to expose the tub and motor assembly. Inspected the belt and it seemed worn and a lot of rubber particles were in base of machine. Ordered the belt from partselect - received i
... Read moret two days later. Loosened 4 motor mount nuts. Removed old belt and replaced. Tightened belt and tightened nuts on motor. Only tricky part is you will need extensions for socket drive because belt is in the way for two of the motor mount nuts. I used a 1/4" small socket wrench, with an extension. No expertise needed on this one.
My washer was making noise but not agitating or spinning on any of the cycles that I turned the dial to. Didn't know if it was the transmission or something simple. I did some research and discovered it may be the belt, even though the belt looked new, I changed it anyway by just removing the front of the washer and cutting the belt off a
... Read morend putting the new belt on by just turning the pulleys until it fed on. No need to tip it over to do the repair...and it WORKED!! Then I did the happy dance around the house...see woman can repair 2!
## WHAT I WISH I'D KNOWN BEFORE I STARTED ## 1. Remove the four hoses first. 2. remove the three screws holding the pump to the structure above BEFORE loosening the flex clamp. 3. with the pump free of the hoses and rest of the washer, then remove the flex coupling clamp from the pump end only; do not remove the flex coupli
... Read moreng from the motor. 4. remove the old pump. 5. attach the new pump to the top of the flex coupling BEFORE attaching the pump to the upper part of the washer. This is the most difficult step, to get the flex coupling on the pump in a secure fashion using the clamp. It's much easier to do if the pump is not yet connected to the rest of the washer. 6. attach the pump to the washer with the three mounting screws. 7. re-attach the hoses. 8. run the washer and check for leaks.
I made the mistake of taking the flex coupling off the motor then tried to put the flex coupling on the motor and the pump when the pump was already attached to the washer. Major grief :>(