This door lock and switch assembly is manufactured to lock the door on your front load washer to prevent it from opening while it is running. You may need to replace the door lock and switch if the do...
This shock absorber kit is an authentic OEM part that is sourced directly from the manufacturer. The kit includes two dual-stage shock absorbers, one spare shock mounting pin, and four locking nuts. T...
The water inlet valve has two ports for water to enter and controls the flow of water into a washing machine. Hot, cold, and warm water can easily enter the washer this way. If the water inlet valve i...
This is a single spring with insulator, but you may also know it as a suspension spring. It is a part for your washing machine. If your tub is no longer stable, which would cause shaking, moving, and ...
This drain hose is designed for use in your washer. The function of this part is to carry water from the drain pump to the house drain. If your washer is leaking or will not drain, you may need to rep...
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
This is a drive belt for your washing machine. This part spins the basket in your appliance by connecting the drive motor to the drive system. You will need to replace the drive belt if your pumps are...
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
3 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Tracy
December 22, 2023
How do I definitely figure out if I have a bad Timer (#131583200) or Speed Control Unit (#131725300)? I've used the Tech Sheet & Schematics to trouble shoot an intermittent problem of the main motor not getting any power. I don't find the issue; put it back together and then it starts working again. The next time I try to use it, the same thing happens again. Everything else is working normally.
For model number FWT445GES2
Hi Tracy, thank you for the question. The motor control board, part number PS418639, for your unit is a separate circuit board that receives signals from the main control or the timer to activate the drive motor. It controls the drive motor speed as well as the direction for the spin and tumble actions during the cycle. You may need to inspect the board for any visible damage. You can do a continuity test on the board to make sure if it is faulty or not. If it is faulty, you may need to replace it. We hope this sorts out your problem!
Replaced shocks but drum still banging violently , seems quite loose inside.
For model number FWT445GES2
Hi Carl, thank you for the question. Make sure suspension springs are fine. If this is not the issue, we would recommend replacing the rear drum with bearing, part number PS418071. Good luck with your repair!
Hello John, Thank you for your inquiry. To remove this part, you would need to take out the screws on the top panel bracket and the top should lift off. Good luck with your repair.
First, I had to remove 2 screws to take off the 2 broken pieces of the door catch. Then I put the new one on using the same 2 screws. The door is now able to close, but does not lock properly. In order to make it work, I put a thin piece of rubber into the place where the door meets the machine. This causes the lock to engage and the
... Read moremachine to work. I don't know how much longer it will work since the repairman claims that the main bearing is going, but hopefully it will last a bit longer.
Part Select got the part to me in one day using the standard shipping, which was impressive. I just wish that I hadn't wasted money on calling a repairman only to have him tell me that he didn't have the part. He charged for the visit anyway even though I told him ahead of time the problem and the model of my machine.
1. Unplug unit. 2. Unscrew 2 nuts holding top in place in rear of unit using phillips head screwdriver. 3.Slide top back and remove. 4. Open door of washer and unscrew 2 screws holding in door lock unit. 5.Pull out unit from the top and install new unit reconnecting the 3 wire connections.
removed 2 screws and removed top access cover. removed 2 screws and removed front access cover. removed 4 retaining pins (one with nammer and punch because it was stuck) connected lower ends of new shocks with plastic pins, extended each shock to slip fit and connected upper ends to wash tub mounts. Reinstalled panels. I wish I could sa
... Read morey that it all went well from there but......when the shocks broke, apparently the hit the motor took was enough to cause an electronic failure of the speed cycle control chip. Now Im waiting for that part.