This lid lock, also known as a door lock, is a genuine OEM replacement part for your washing machine. The lid lock keeps your washer lid closed during the washing cycle. If this part is broken, your w...
This drain pump assembly is for washers. Drain pump assembly removes water from the washer during the drain portion of the cycle. The assembly may include multiple parts; refer to your parts diagram f...
This lid lock striker is sourced directly from the manufacturer for use in top-load washing machines. It is a white, plastic component located on the underside of the washing machine lid. When the lid...
This is a drive belt for various models of dryer. This belt is responsible for allowing the drive motor to rotate the dryer drum. Over time and with use, this belt will wear out and if it becomes dama...
This is an agitator assembly for washing machines. Agitators are used within top load washing machines to move back and forth and effectively wash your clothes. However, if the agitator currently in y...
This is a water inlet valve; an electrically controlled solenoid valve that opens and closes when necessary, to control the flow of water into your washing machine during the washing cycle. This part ...
This lid lock bezel, also known as a trim piece, is a genuine OEM part designed for washing machines. It is approximately 3.5 inches long. The bezel is a white, plastic frame that fits around the peri...
This is a clutch for your washing machine. The clutch is made of a white plastic material and is used within washing machines to engage and disengage the transmission during the wash and spin cycles, ...
This is a mode shifter or shift actuator for models of washing machine. Mode shifters are designed to change the function of the washing machine motor, between spinning cycles and agitation, and is us...
This is a speed sensor for a variety of washing machine models. Speed sensors are used to monitor the speed of the washer drum and communicate it to the electronic control board to slow or quicken it....
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
11 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Linda
August 23, 2021
Can you tell me how to add fabric softener with this machine? Thanks
For model number GTW220ACK6WW
Hello Linda, Thank you for your inquiry. For this model, you would pour the diluted fabric softener directly into the tub water during the rinse cycle. You can also have a fabric soften dispenser cap added. Hope this helps.
Hello Dasie, thank you for getting in touch. It appears that your washer may have a damaged lid lock assembly, part number PS16554755. You may need to replace the lid lock assembly to fix this issue. We hope that helps!
Washer fills and drains. But
Doesn't wash or spin.
What's the problem?
For model number GTW220ACK6WW
Hi Kathryn, thank you for your question! Check if the lid is properly closed. Some washing machines have a safety feature that prevents them from spinning if the lid is open. Make sure the drive belt is fine. If all checks are fine, you may need to replace the motor, part number PS12743595. We hope that helps!
Hi Debra, thank you for the question. According to our research, the lid lock service kit for your model is part number PS16554755. Glad to be of help!
Drain all the water out of the tub with a shop vac Remove rear drain hose and drained rest of water into a bucket Remove small rear panel (bottom left hand corner) where the drain hose connects Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans Remove internal drain hose/clamps
... Read morefrom pump - w/ pliers Remove belt cover (gray plastic) with socket - 3 bolts Remove wire assembly plug from socket Remove old drain pump with socket - 3 bolts Install new drain pump - 3 bolts - plug wire assembly into socket Reinstall belt cover - 3 bolts Reinstall hose to drain pump (note panel will be inside washer) Feed drain hose panel through hole and reinstall - 1 nut Re attached drain hose to exterior drain plug You are done !
Very simple to repair. Be sure to drain the tub outside or into the sump pump then lay the washer on its side. The pump is right there on the bottom of the basket with 3 bolts. You will also need to remove the belt cover to get to the plug. So simple and saves you hundreds off repair man prices.