Models
>
JDR8895AAS
JDR8895AAS Whirlpool Range - Overview
Sections of the JDR8895AAS
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Long Oven Sensor
PartSelect #: PS1570174
Manufacturer #: 12001656
This long oven sensor is also commonly known as a temperature sensor. It is designed for use with ovens and ranges. It is similar to a thermostat; it measures and regulates the internal temperature of...
$34.75
In Stock
Burner Knob
PartSelect #: PS11744380
Manufacturer #: WP74010205
This knob accepts a D-shaped shaft. Sold individually.
$32.52
In Stock
Torx Screw
PartSelect #: PS11741257
Manufacturer #: WP3368921
7-18 x 3/4" - sold individually.
$6.54
In Stock
Screw
PartSelect #: PS12349731
Manufacturer #: W11233072
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$20.79
In Stock
Screw with Washer
PartSelect #: PS11744138
Manufacturer #: WP74006515
This is a replacement screw and washer for your oven/range. It is a Phillips-head screw approximately half an inch long, and the washer is approximately 1 inch in diameter. The screw attaches the oven...
$7.95
In Stock
Surface Burner Spark Igniter
PartSelect #: PS11746068
Manufacturer #: WP8523793
This part helps your burner ignite and produce flame.
$25.35
In Stock
Upper Bake Element - 240V
PartSelect #: PS2082040
Manufacturer #: 74004105
This bake element is found on the bottom of the oven.
$104.96
In Stock
Broil Element
PartSelect #: PS11752536
Manufacturer #: WPW10310249
This broil element is found on the roof of the oven.
$99.73
In Stock
Burner Cap
PartSelect #: PS11745641
Manufacturer #: WP8284669
Burner Cap - 6000 BTU
Sold individually.
$55.11
In Stock
Questions And Answers for JDR8895AAS
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the JDR8895AAS
[Viewing 11 of 11]Little to no heat when baking
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Oven is too hot
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Little to no heat when broiling
Fixed by
these parts
these parts
Show All
Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Touchpad does not respond
Fixed by
these parts
these parts
Show All
Will not program
Fixed by
these parts
these parts
Show All
Door won’t open after self cleaning cycle
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven not holding 350 F, when cooling the coils did not reheat
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening,
... Read more
reinstall 2 screws. The oven works fine! Note that due to thermal lag the temperature overshoots to 370 degrees and undershoots to 340 degrees, this appears to be normal oven operation. Putting door back in place was easy.
Read less
Parts Used:
-
David from Westford, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
156 of 196 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
F1-1 code
First I removed the two screws that hold the element in place. I then pulled the sensor out about 3 inches and disconnected the two wires. Next, I connected new sensor and screwed the new sensor back in place. One area for caution. Make sure that the electrical connection is pushed in past the insulation on the back side of the oven. Fa
... Read more
ilure to do so will cause the plastic plug connector to melt from oven heat.
Read less
Parts Used:
-
charles from marstons mills, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
74 of 99 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Right front ignitor switch not operating, possibly got wet when being cleaned.
The truth....This procedure will take 40 minutes total for the average "mechanic".
You will need a #2 phillips screwdriver and two open end wrenches, 1/2" and 5/8"
AFTER unplugging the power cord AND turning
OFF the gas feed:
1-Remove seven phillips head screws from largest rear panel, and remove pa ... Read more nel.
2-Disconnect the gas feedline from the manifold with 5/8" open end wrench.
3-Unplug switch "set" ( 2 connectors, one inline and one spade)
4-Open top oven door and remove two hexhead/phillips screws from underside of stovetop, located on far right and far left forward corners.
5-Pull stovetop forward to unlatch from rear holddown clips on frame.
6-Lift stovetop up enough to disconnect five gas burner supply lines from control valves with 1/2" open end wrench.
7-Remove two phillips head manifold attaching screws from topside of control valves (visible after pulling off control valve knobs)...manifold is now free, remove from stove.
8-"Pop off" switches from control valves, and snap new set into place.
9-Install drip shield disks on control valve shafts.
10-Reverse procedure to reassemble stove.
NOTES:
1-Remember to install drip shield disks on control valve shafts before reattaching manifold to stovetop.
2-Check all visible screws for tightness now that the covers are removed, ....you WILL find loose screws...Avoid overtightening/stripping screw holes.
You will need a #2 phillips screwdriver and two open end wrenches, 1/2" and 5/8"
AFTER unplugging the power cord AND turning
OFF the gas feed:
1-Remove seven phillips head screws from largest rear panel, and remove pa ... Read more nel.
2-Disconnect the gas feedline from the manifold with 5/8" open end wrench.
3-Unplug switch "set" ( 2 connectors, one inline and one spade)
4-Open top oven door and remove two hexhead/phillips screws from underside of stovetop, located on far right and far left forward corners.
5-Pull stovetop forward to unlatch from rear holddown clips on frame.
6-Lift stovetop up enough to disconnect five gas burner supply lines from control valves with 1/2" open end wrench.
7-Remove two phillips head manifold attaching screws from topside of control valves (visible after pulling off control valve knobs)...manifold is now free, remove from stove.
8-"Pop off" switches from control valves, and snap new set into place.
9-Install drip shield disks on control valve shafts.
10-Reverse procedure to reassemble stove.
NOTES:
1-Remember to install drip shield disks on control valve shafts before reattaching manifold to stovetop.
2-Check all visible screws for tightness now that the covers are removed, ....you WILL find loose screws...Avoid overtightening/stripping screw holes.
Read less
Parts Used:
-
Lou from Fort Pierce, FL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Wrench set
33 of 33 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!