Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
The point of the lid switch is for the tub to stop spinning when the washer lid is opened. It is a safety precaution just in case someone decides to stick their hand inside the washer while the tub is spinning.
$47.93
In Stock
Order within the next 3 hrs and your part ships today!
This drive hub kit (part number W10528947VP) is for washers.
Drive hub kit W10528947VP connects the spin basket to the spin shaft that spins the basket. The kit may include multiple parts; refer to...
$34.00
In Stock
Order within the next 3 hrs and your part ships today!
This is a replacement clutch assembly or cam kit for your washer. The clutch assembly is mounted on the drive shaft on the bottom of your washer. You may need to replace the clutch assembly if the spl...
$54.48
In Stock
Order within the next 3 hrs and your part ships today!
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
$8.02
In Stock
Order within the next 3 hrs and your part ships today!
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
$87.18
In Stock
Order within the next 3 hrs and your part ships today!
This suspension rod kit is a genuine OEM replacement kit that is compatible with various models of washing machine. The kit is responsible for supporting the inner tub of the washing machine and absor...
$113.79
In Stock
Order within the next 3 hrs and your part ships today!
This part is the replacement lid latch or latch assembly for your top-load washer. The lid latch holds your washer door closed, and allows the washer to run its cycle. If the lid latch is damaged, you...
$44.48
In Stock
Order within the next 3 hrs and your part ships today!
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
$11.12
In Stock
Order within the next 3 hrs and your part ships today!
This wash plate is for washers
Unplug the washer and shut off the water supply before installing this part
$128.38
In Stock
Order within the next 3 hrs and your part ships today!
Questions And Answers for MVWC555DW0
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
17 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Sallie
February 25, 2020
Machine suddenly stopped spinning, sound like it tries then stops. I have audio if you want to hear it, who should i call or what should i do? Thanks
For model number MVWC555DW0
Hello Sallie, thank you for your question. If the unit tries to spin but will not actually get into the fast spin, the most likely issue is PartSelect Number: PS11769864 shift actuator. This moves the unit from agitate to spin. We have an installation video on our site on how to replace that. Good luck with your repair.
What to do to stop clothes from being left sopping wet after wash cycle? Even after spin and drain cycle.
For model number MVWC555DW0
Hello, Thank you for your question. If your washer will not spin out all water and clothes are still wet, the drain pump might be clogged with debris or possibly faulty. There could be a foreign object that is stuck in the pump and inside the drain hose.Check that, and then you will also want to check your lid switch. We hope this helps, good luck with this repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Joel
August 6, 2021
Washing machine will not fill with water
For model number MVWC555DW0
Hello Joel, Thank you for the question. Normally this is an indication the Water Inlet Valve is defective and may need to be replaced. We hope this helps!
Hello Joel, Thank you for contacting us. Normally if the Washer is not filling with water and it is powering on normally, the Water Inlet Valve is defective and may need to be replaced. We hope this helps!
Hello Lee, We have a general installation video that will show you how these types of parts are installed in an washing machine. You can view that here: https://www.youtube.com/watch?v=2slahiXRGow. Good luck with your repair.
The instructions that came with the part were worthless. Essentially, unplug, put in new part, plug it back in. I spent a considerable amount of time on the internet and finally found a video showing how to open the top. Unlike other models, it is held down by clamps in the back rather than clips in the front. Once finding this inform
... Read moreation the installation was simple. Remove the clamps and the back of the console, slide the top forward and lift, remove and replace the lock and reassemble. You don't even have to remove the hoses.
Well, first investigated and found loose nut on drive clutch. First take off the two screws with nut drive then cover off using a screwdriver blade to snap off the cover. Then socket ratchet to take off the nut on drive clutch. take off belt by slowly rotating the drive gear. two screws that hold the electronics to the upper drive clutch
... Read moreand put aside, so you can snap off the cover for drive clutch on upper part with screwdriver and off the parts come and install whole unit back as took it apart. Line up the new upper clutch so that is position as was before. (Using parts diagram helps a lot as www. partsselect.com has for you or Maytag.com.) Then put the electronic part board back on and the gear and nut. Make sure it is tight by several attempts to make sure it's snugged up good and then slowly roll belt back on the pulley and motor drive. Put your cover guard back on with two screws and done.
ordered hub and it shipped quickly. I was able to put the hub in place and screw the screws in. you want to tighten them down slowly and go around to each screw tightening a little at a time so you don't break the hub. as you tighten the screws down the hub slides down flush. its impossible to just push the hub on with your hand. Buttoned
... Read more it back up and got caught up on laundry. good day when the washer is fixed.
