Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
Murray Snow Blower Belts
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Murray Snow Blower Belts
Murray Snow Blower Belt, Drive
2) This repair may be quite simple or it may be a huge problem, depending on whether the manufacturing problem described below is present.
3) The space between the housing and aluminum pulley is so tight that a belt CANNOT be fit through it!
Therefore, the only way to replace the belt is to remove the pulley.
* * * * * * * * * * * * * * * * * *
Step 1. As with every other single stage snow blower, remove the belt cover held by six 10 mm bolts. This may require a metric nutdriver or a deep socket for a couple of bolts.
Step 2. Use a 17 mm wrench to remove the large nut holding the aluminum impeller pulley, along with the flat and split lock washers. Also remove the part that locks the pulley onto the shaft.
Step 3a. If there is not a manufacturing issue, the pulley will come off easily and you may proceed to thread the new belt around the power and idler pulleys.
Step 3b. IF THE PULLEY DOES NOT COME OFF, you may need to get a wheeler puller tool to get it loose and off the shaft. Once the overly tight pulley is off, you may wish to file down the shaft near the end until the pulley slides on and off without much effort. (You may also wish to apply a dry silicone lubricant to the shaft to make the job easier next time.)
Step 4. In order the install the new belt, feed it around the power pulley and the idler pulley controlled by the "engage" handle. With the impeller pulley still off its shaft, feed the belt around it, fitting the belt grooves into the pulley grooves.
Step 5. The large aluminum can be replaced on its shaft, followed by the pulley lock, flat washer and split ring washer. Tighten the pulley lock nut, holding the impeller blades to keep the shaft from turning.
Step 6. Replace the belt cover and the six bolts holding it in place. Read more...
PartSelect Number PS8894608
Manufacturer Part Number 1739338YP
Installation Instructions
julianne from CEDAR RAPIDS, IA
Initially, belt came off, lodged between pulley and housing. When replace, belt broke
NOTES: 1) This is not a new model, but a rebranded version - previously under Murray, Simpliticy, Snapper, etc., so parts are available, but not readily identified yet.2) This repair may be quite simple or it may be a huge problem, depending on whether the manufacturing problem described below is present.
3) The space between the housing and aluminum pulley is so tight that a belt CANNOT be fit through it!
Therefore, the only way to replace the belt is to remove the pulley.
* * * * * * * * * * * * * * * * * *
Step 1. As with every other single stage snow blower, remove the belt cover held by six 10 mm bolts. This may require a metric nutdriver or a deep socket for a couple of bolts.
Step 2. Use a 17 mm wrench to remove the large nut holding the aluminum impeller pulley, along with the flat and split lock washers. Also remove the part that locks the pulley onto the shaft.
Step 3a. If there is not a manufacturing issue, the pulley will come off easily and you may proceed to thread the new belt around the power and idler pulleys.
Step 3b. IF THE PULLEY DOES NOT COME OFF, you may need to get a wheeler puller tool to get it loose and off the shaft. Once the overly tight pulley is off, you may wish to file down the shaft near the end until the pulley slides on and off without much effort. (You may also wish to apply a dry silicone lubricant to the shaft to make the job easier next time.)
Step 4. In order the install the new belt, feed it around the power pulley and the idler pulley controlled by the "engage" handle. With the impeller pulley still off its shaft, feed the belt around it, fitting the belt grooves into the pulley grooves.
Step 5. The large aluminum can be replaced on its shaft, followed by the pulley lock, flat washer and split ring washer. Tighten the pulley lock nut, holding the impeller blades to keep the shaft from turning.
Step 6. Replace the belt cover and the six bolts holding it in place. Read more...