Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
General Electric Microwave Oven Combo Circuit Boards and Touch Pads
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular General Electric Microwave Oven Combo Circuit Boards and Touch Pads
General Electric Microwave Oven Combo Display Control Board
PartSelect Number PS1022528
Manufacturer Part Number WB27X10858
Fixes these symptoms
- Touchpad does not respond
- See more...
General Electric Microwave Oven Combo Digitron
Step one: Disconnect the power to the Advantium 120. Unplug unit, trip the breaker, whatever. Your responsibility to make sure the electrical power is removed.
For cabinet mounted units remove four screws from front side flange holding the microwave to cabinet
On the cabinet mounted model access three screws along the top front edge of case behind the display then one screw on each side of display and two hidden screws accessed through the top of the case via access holes. (use a magnetic see driver for these screws)
Work the display panel off and support it until the connectors are removed.
There are three small color coded plugs on the left side to the PC board and five larger colored plugs on the right side. Note plug locations.
Lay the removed control panel upside down on a towel at the corner of the sink so the selector knob is not resting on the counter.
Remove PC plug to the display and remove four screws on the PC board. Shift the PC board to release the tabs. Then remove two screws holding the PC display board. Note two guide pins also align the PC board.
Remove the rubber insulator from the old board and put it at the same location on the new board. There is usually enough stickiness on this insulator to put it back on the new board.
Installation is reverse. Reconnect power. Try it out after completion by boiling water in a microwave safe container. My new display was much brighter than the replaced display. No flashing. Read more...
PartSelect Number PS1018741
Manufacturer Part Number WB27X10856
Installation Instructions
William from EAGLE, ID
Flashing display
Replace Advantium 120 flashing display.Step one: Disconnect the power to the Advantium 120. Unplug unit, trip the breaker, whatever. Your responsibility to make sure the electrical power is removed.
For cabinet mounted units remove four screws from front side flange holding the microwave to cabinet
On the cabinet mounted model access three screws along the top front edge of case behind the display then one screw on each side of display and two hidden screws accessed through the top of the case via access holes. (use a magnetic see driver for these screws)
Work the display panel off and support it until the connectors are removed.
There are three small color coded plugs on the left side to the PC board and five larger colored plugs on the right side. Note plug locations.
Lay the removed control panel upside down on a towel at the corner of the sink so the selector knob is not resting on the counter.
Remove PC plug to the display and remove four screws on the PC board. Shift the PC board to release the tabs. Then remove two screws holding the PC display board. Note two guide pins also align the PC board.
Remove the rubber insulator from the old board and put it at the same location on the new board. There is usually enough stickiness on this insulator to put it back on the new board.
Installation is reverse. Reconnect power. Try it out after completion by boiling water in a microwave safe container. My new display was much brighter than the replaced display. No flashing. Read more...
General Electric Microwave Oven Combo Electronic Clock Oven Control
PartSelect Number PS773585
Manufacturer Part Number WB27T10411
Please note: With this control the wiring could be differ from the original. It will possibly need to be installed by an appliance repair person.
General Electric Microwave Oven Combo POWER BOARD
PartSelect Number PS1020967
Manufacturer Part Number WB27X10861
General Electric Microwave Oven Combo Oven Control
PartSelect Number PS953726
Manufacturer Part Number WB27T10500
Installation Instructions
Gary from CHAPEL HILL, NC
Oven stopped heating and heating element tested good
Ordered the oven control board and installed the new board by removing one wire at a time.
Read more...
General Electric Microwave Oven Combo Electronic Oven Control Board
PartSelect Number PS1517470
Manufacturer Part Number WB27T10914
General Electric Microwave Oven Combo Electronic Clock and Timer Kit
PartSelect Number PS233996
Manufacturer Part Number WB19X10006
This electronic clock replaces the mechanical clocks with a more reliable digital timer. As per the manufacturer, this part should be installed by appliance repair person.
Fixes these symptoms
- Timer will not advance
- See more...
Installation Instructions
David from Owings Mills, MD
Electronic Timer went out and Top Oven No Longer worked
There are about 12 wires behind the panel...and this was the second time I've replaced the electronic clock in the past four years. I replaced the analog clock four years ago with the digital version because the analog was no longer available, so I knew what I was in for. There are four screw (top of the frame and lower frame) to remove before the frame holding the clock will come out. First DISCONNECT the power! You've have to remove the clock control knobs, and the plastic lever on the self cleaning handle. The first time I ordered this replacement part from PartsSelect there was a diagram included on which wire goes where. This time there wasn't! So it gets a little complicated. Make sure you label all the wired before you disconnect the old clock panel. Anyway, remove the four nuts holding the old clock in place; put the new clock panel in; replace the four nuts. I'll be glad to talk anyone through the rest and I have photos of the whole repair.
Read more...
General Electric Microwave Oven Combo CONTROL OVN (ERC3DD)
PartSelect Number PS953700
Manufacturer Part Number WB27T10435
Installation Instructions
Steven from Ruckersville, VA
hole punched through digital panel display
The parts arrived in well packaged boxes with extra protection. The parts online listing described and illustrated better than any other supplier, a big help for me. This was a brand new convection double wall oven, damaged and discounted. repair was a snap just removing each terminal one at a time and reconnecting to the new control. I will definitely use PartSelect again already replacing parts in our two year old dishwasher, the parts are a bargain at PartSelect. Thanks so much for being a great and easy way to shop and save. Steve C.
Read more...
General Electric Microwave Oven Combo Oven Control with Harness
2. Remove grill that around built in microwave; remove two top screws and to bottom (open oven door).
3. Remove two screws on the control panel.
4. Swing out and allow panel to suspend from its wire holder.
5. Trace the two harness cables from the old control board and disconnect from the counterparts inside the unit.
6. Remove the "ribbon" connector (do not damage, be gentle)
7. Remove the four screws holding the old control in place.
8. Place the new control board in place (do not connect the ribbon connector yet).
9. Plug in the harness to their respective receiving locations in the unit.
10. Install the "ribbon" connector into the new control panel.
11. Reverse steps 4-1 above ensuring all connections are solid and made correctly.
12. Turn on the circuit breaker and enjoy a "like new" oven! Read more...
PartSelect Number PS953773
Manufacturer Part Number WB27T10566
Installation Instructions
WILLIAM from FRANKLIN, OH
Oven Panel lights too dim to read and probe stopped working
1. Turn off breaker2. Remove grill that around built in microwave; remove two top screws and to bottom (open oven door).
3. Remove two screws on the control panel.
4. Swing out and allow panel to suspend from its wire holder.
5. Trace the two harness cables from the old control board and disconnect from the counterparts inside the unit.
6. Remove the "ribbon" connector (do not damage, be gentle)
7. Remove the four screws holding the old control in place.
8. Place the new control board in place (do not connect the ribbon connector yet).
9. Plug in the harness to their respective receiving locations in the unit.
10. Install the "ribbon" connector into the new control panel.
11. Reverse steps 4-1 above ensuring all connections are solid and made correctly.
12. Turn on the circuit breaker and enjoy a "like new" oven! Read more...
Related General Electric Microwave Oven Combo Parts
- All General Electric Microwave Oven Combo parts
- General Electric Microwave Oven Combo Brackets and Flanges
- General Electric Microwave Oven Combo Doors
- General Electric Microwave Oven Combo Drawers and Glides
- General Electric Microwave Oven Combo Elements and Burners
- General Electric Microwave Oven Combo Glass Tray and Supports
- General Electric Microwave Oven Combo Handles
- General Electric Microwave Oven Combo Hardware
- General Electric Microwave Oven Combo Hinges
- General Electric Microwave Oven Combo Knobs
- General Electric Microwave Oven Combo Lights and Bulbs
- General Electric Microwave Oven Combo Racks
- General Electric Microwave Oven Combo Seals and Gaskets
- General Electric Microwave Oven Combo Sensors
- General Electric Microwave Oven Combo Switches
- General Electric Microwave Oven Combo Thermostats
- General Electric Microwave Oven Combo Trims