General Electric Microwave Oven Combo Switches

Your Price

$45.43

General Electric Microwave Oven Combo Secondary Door Switch

★★★★★

45 Reviews

PartSelect Number PS237421

Manufacturer Part Number WB24X829

The secondary door switch is a simple on/off mechanism that stops the microwave from operating when the door is open (normally opened). The switch monitors the door latch position, and communicates whether the door is open or closed to the electrical control board. This door switch is approximately 1 inch long, and has 2 metal prongs called terminals that extend out of its body. Common symptoms related to a faulty secondary door switch include: microwave will not turn/shut off, or the microwave will not heat properly. NOTE: Before you begin this repair, first make sure your microwave is unplugged, and that your capacitor is discharged. A capacitor stores large amounts of electricity even when your microwave is unplugged.

Fixes these symptoms

Doesn’t shut off
No heat
Touchpad does not respond
See more...

Installation Instructions

Marla from Arlington, TX

light worked, timer and control pad worked, but no turntable, no heat, no noises of any sort, just didn't start up

Noted on partselect.com that someone else with this problem, found it to be secondary door switch. There are three door switches in this model, but online info noted that one of the three might feel "soft" (in my case, one switch clicked in a rather "jiggly" way, the other two were strong decisive clicks.) To access the door switches on this model was the only difficult part. First use a torx bit to remove the two torx screws below the latches inside the microwave. This frees the latching part inside, that holds the door switches, which you will remove after you take off the control panel. The top grill has to come off before you can remove the door panel. Remove the screws above the grill, on the microwave top cover, The grill on this model is covered with a panel that moves out when it vents. After removing the two top screws, the covered grill vent slides left to remove. Be careful, as the sliding tabs are plastic. Wiggle and jiggle it, to slip it off. Below the removed grill, is a small metal grill with one screw in lower center. Remove that screw, and wiggle that out. You'll then see the one screw that holds on the control panel. Remove this screw, and lift the control panel up to remove. Again, go slowly and gently, as the bottom tabs holding the control panel in, are also plastic and easily broken. Lay the control panel on something, (I used the coffee maker) and pull out the wire bundles tucked on the left, that are attached to the latching panel. Wiggle the latching panel gently to lift it up off of it's plastic tabs and pull it out towards you, so you can see the three door switches. Each switch (part number WB24X829) has a little black switch on it. Feel each switch with either your finger, or a screwdriver to see which one doesn't "click" strongly. The weak one is the one you will replace. The door switches are fitted into a tab, and plugged into their wires. Remove the defective switch, pull out the wires, and replace it with the new switch, plugging back the wires, and slipping it back into it's plastic tabs. Then put everything back together in reverse order. The entire job took me fifteen minutes EXCEPT for figuring out how to slide off the upper grill, which I have told you. A repairman would have cost $150, the part was $18. AND, there's a good chance, the other two switches will get "used up" in the next year or so as well, so I'll be ready next time. Thank you, Partselect, why work all day, to make money, only to give it to somebody else, for fifteen minutes of work. All I needed was the knowledge. Read more...

Your Price

$33.50

General Electric Microwave Oven Combo Primary Door Interlock Switch

★★★★★

18 Reviews

PartSelect Number PS237015

Manufacturer Part Number WB24X10047

This interlock switch is located in the door latch.

Fixes these symptoms

Doesn’t shut off
No heat
Tray won’t turn
See more...

Installation Instructions

Steven from Manassas, VA

Microwave not heating

Rmovd top vent screen. Removed control panel. Removed fuse cover panel. Replaced fuse. Removed housing of door switches. Removd wiring from door switches and and removed door switches from housing. Replaced with new switches and re-connectd wiring. Re-attached panels. Read more...

Your Price

$37.09

General Electric Microwave Oven Combo Monitor Door Switch

★★★★★

14 Reviews

PartSelect Number PS237422

Manufacturer Part Number WB24X830

Unplug your microwave before attempting this repair. You will need to remove the grill, which is held into place by two screws at the top of the grill (open your microwave door before doing this). Remove the grill. Remove the screw on the left holding the control panel in place. Loosen the screw behind the panel. You should now be able to lift the panel up and pull forward to detach. You will find the door switch by removing the screws to detach the switch assembly. Press on the release tab to remove the middle switch. Disconnect the wire connector to release the old switch. The door switch is normally closed.

Fixes these symptoms

Doesn’t shut off
No heat
Won’t turn on
See more...

Installation Instructions

George from Sugar Land, TX

GE Microwave turns on when door is opened

I saw a similar problem description at partselect.com and was confident to take the challenge to repair it myself. (Thanks to partselect.com). When I opened the microwave cover I found 3 similar switches. 2 of them works the same way and the other in reverse direction. Image diagram provided to buy parts is helpful to identify the switch.
Steps:
Remove the built-in microwave from the wall and keep it in an open space.
Remove the microwave screws and take the cover out.
Remove the 2 screws(inside) from the plastic panel where switches are snapped in
Gently remove the faulty switch and replace with the new one.
(In my case the topmost secondary door switch was broken) Read more...

Your Price

$87.28

General Electric Microwave Oven Combo Dual Burner Control Switch

★★★★★

15 Reviews

PartSelect Number PS236785

Manufacturer Part Number WB24T10063

This switch controls the dual burner.

Fixes these symptoms

Element will not heat
See more...

Installation Instructions

Jeff from Clinton, IA

No control of right front burner (dual burner)

The burner would work but you could not regulate the heat. I ordered and replaced the control switch for that burner. The part was like for like and reasonably priced compared to other websites and dealer. The picture showed that it was identical. I ordered one day and it was here the next. I had drawn a diagram of where the wires went on the old switch so it was very easy to replace. Probably took me 15 minutes or so. Works perfectly and by buying from this website it saved me a few bucks. Read more...

Your Price

$48.27

General Electric Microwave Oven Combo Infinite Switch Control

★★★★★

3 Reviews

PartSelect Number PS236751

Manufacturer Part Number WB24T10026

This surface element control switch is for ranges. Surface element control switch turns the surface element on and off and controls how much heat the element produces. Unplug the range or shut off the house circuit breaker for the range before installing this part. Wear work gloves to protect your hands.

Fixes these symptoms

Element will not heat
See more...

Installation Instructions

manuel from key west, FL

left front burner would not turn on

Removed panel to gain access, removed wires from switch from burner that was not operating and attached them to switch for burner that was working. Burner worked, problem identified. Replaced bad switch with new switch. Problem solved. Read more...

Your Price

$42.24

General Electric Microwave Oven Combo Infinite Warmer Switch

★★★★★

1 Review

PartSelect Number PS236739

Manufacturer Part Number WB24T10012

Your Price

$31.39

General Electric Microwave Oven Combo SWITCH SPDT HIGH AMP

★★★★★

3 Reviews

PartSelect Number PS1765837

Manufacturer Part Number WB24T10147

This light switch is controlled by opening and closing the oven door

Installation Instructions

Michael from Albuquerque, NM

Convection oven fan and door light not working

The first step was to determine whether the problem was with the fan itself or the switch. I did this by opening the back cover and using a Volt meter to verify that the fan was not getting power. (I could have skipped this step.)

Next, I unplugged the range, closed up the back cover and lifted the range hood by removing two hex head screws that are just inside and on either side of the top of the opening in the range door. Propping the hood open, I removed the connector leading to the switch, then pushed the switch out the front. Inspection showed that the switch was damaged so I closed up the range and ordered the part from Part Select. Once the part arrived, it was a 15 minute job to unplug the range, lift the top, install the new switch, and close up the unit.

Caution. On starting to install the switch, I failed to unplug the range and my finger brushed one of the hot contacts leading to the switch. Thankfully, I was not injured. Do not repeat my mistake on this issue. Unplug the range even if you're only installing this simple switch. Read more...

Your Price

$59.79

General Electric Microwave Oven Combo Limit Switch

★★★★★

1 Review

PartSelect Number PS236592

Manufacturer Part Number WB24K5033

This part acts like a safety thermostat on the appliance. Once it reaches a certain temperature it will shut off the heat source (element) to make sure the temperature doesn't go any higher.

Installation Instructions

Arno from Sacramento, CA

Oven stops heating and states F3 error code.

The most obbious suspect is the upper oven fan. Turned off power circuit breaker. Removed two philip screws at top of control panel and lowered the panel. Using the 3D view of the oven on this web site I located the fan limit switch. Jumpered the limit switch. Turned power on and the fan ran. That proved the switch was defective and not the fan. Replaced the limit I purchased from Partselect.com.

Please note* My life career was electrical. I used the schematic that came with the oven to determine that the limit was the only control between one of the 240 volt lines and the fan. Thus I knew it was safe to jump the limit.

If you are in doubt, seek some advice.
Good Luck, Arno Read more...