General Electric Microwave Oven Combo Sensors

Videos!

Your Price

$38.48

General Electric Microwave Oven Combo Temperature Sensor

★★★★★

48 Reviews

PartSelect Number PS10059162

Manufacturer Part Number WB21X22134

The temperature sensor, also known as the oven temperature sensor assembly is usually found in the back of the oven. The function of the oven temperature sensor assembly is to measure the temperature inside your oven while it is on and send the temperature back up to the electronic control, which adjusts as necessary. If your oven is having difficulty achieving warmer temperatures and/or keeping warmer temperatures up, you may want to test your temperature sensor. Before you make this repair remember to unplug your range from the power source, and turn off the gas shut off valve.

Fixes these symptoms

Element will not heat
Little to no heat when baking
Little to no heat when broiling
See more...

Installation Instructions

Peter from stamford, CT

Oven would go in to a F2 Error

Removed six 1/4" hex nuts on rear of oven. Then through front/inside removed a single 1/4" hex nut to actually remove sensor. Unplug sensor connector, remove. Reversed steps, push oven back in place and plugged in. Tested oven function. Read more...

Videos!

Your Price

$36.75

General Electric Microwave Oven Combo Oven Sensor

★★★★★

18 Reviews

PartSelect Number PS236398

Manufacturer Part Number WB23T10015

The function of the oven sensor is to detect the temperature within the oven cavity. If you notice that the oven is too hot or too cold, or it is not heating evenly, you may need to replace the oven sensor. The oven sensor is typically located in the back of the oven so you will most likely need to pull your oven out to access it. Many of our customers have rated this repair as easy. You will need a Phillips screwdriver to complete this repair. Be sure to disconnect the power source and shut off the gas valve before doing this repair.

Fixes these symptoms

Element will not heat
Little to no heat when baking
Oven is too hot
See more...

Installation Instructions

Sean from Highlands Ranch, CO

Oven was not coming up to temperature

I had to remove the oven from the wall because the sensor plug connction is behind the unit. Two screws hold the sensor inside the oven and then I disconnected the lead and pulled the sensor out from the front. I installed the new sensor, tightened the two screws holding it in and connected the lead. Then reinstalled the oven into the wall. Overall, a very easy repair once you get the oven out. Read more...

Your Price

$56.84

General Electric Microwave Oven Combo Meat Probe Thermistor

★★★★★

4 Reviews

PartSelect Number PS1481046

Manufacturer Part Number WB20T10024

This probe is used to check the internal temperature of the meat to ensure proper temperature is reached. Also known as a Meat Probe.

Fixes these symptoms

Will not program
See more...

Installation Instructions

robert from FAIRFIELD, OH

Oven meat probe broken

This item worked as described. I paid more for this 'oem' probe than the generic 1 because i didn't want to chance it not working as others have reported.
- works great. tested it....snaps in, reads correctly, snaps out. Read more...

Your Price

$19.22

General Electric Microwave Oven Combo SENSOR Assembly

★★★★★

4 Reviews

PartSelect Number PS8754411

Manufacturer Part Number WB21X10165

Fixes these symptoms

Oven is too hot
See more...

Installation Instructions

Don from HASLET, TX

The oven was burning when cooking at same temperature we always cooked it on

there was one screw holding it on the back wall of the oven. It was easy enough that my daughter installed it with my guidance. Read more...

Videos!

Your Price

$152.00

General Electric Microwave Oven Combo Oven Sensor

★★★★★

5 Reviews

PartSelect Number PS236043

Manufacturer Part Number WB21X5301

It is possible that your oven is cold because of a fault in the temperature sensor. The temperature sensor regulates oven temperature in modern ranges, like a thermostat. It is on the back wall near the broiler on the top wall. On a newer oven, there may be a fault code displayed. Faulty temperature sensors are often responsible for F3 and F4 error messages on an electric range. Check your manual or the manufacturer website to find out the proper resistance of the temperature sensor. To check your sensor, unplug the oven and use a multi-meter to see if your sensor is at the correct resistance.

Fixes these symptoms

Element will not heat
Little to no heat when baking
Oven is too hot
See more...

Installation Instructions

James from Austin, TX

Oven tempature was approximately 150 degrees to low

This repair is EASY if you know how to use an ohm meter. If not, seek help for this step.

SYMPTOM:
The oven (JKP27WOP3WG or JKP27WP3WG and many ovens like it ) was not getting hot enough. Verifying the cooking temperature with an typical oven thermometer, I was able to determine that the oven was cooking temperature was about 150 degrees to low.

FAILURE POINTS:
There are two logical failure points (1) The oven sensor ( WB21X5301 about $75), or the (2) the controller board (PS238233 about $252). In my case it was the controller board. When replaced the oven worked beautifully.

REPAIR:
As with any repair, you MUST DISCONNECT POWER TO THE UNIT BEFORE SERVICING!!!

Pull oven from the wall:
- Disconnect power by flipping the circuit breaker to the OFF position.
- Remove the top flange / cowling from the top of the oven (it just pulls off)
- Remove two screws under the top flange / cowling
- The whole unit easily slides out, but it is highly recommended that you use two people to place the oven on the floor.

As a diagnostic between these two parts, if the oven sensors measure approximately 1.1K ohms of resistance at room temperature, then it is probably not the sensor. The oven sensor wires are connected to two white wires that run up to the controller board. You need to disconnect the oven sensor to make the measurement. You may either completely remove the oven sensor by cutting the wire (be sure to allow yourself enough slack so that they may be safely reconnected) where it connects to the white wires, OR, (preferred method) if leaving the oven sensor partially installed,
- Remove the top sheet metal cover (10 screws)
- Remove the service connect cover (2 screws - this is where the main Power cord comes into the unit)
- Disconnect the white wires from the controller board (this connector which also includes other circuits is on the left side when looking at the controller board).
- Remove two screws from oven sensor but just let in dangle down so that you can put the sensor in the ice water / boiling water.

Measure the resistance under the following conditions. Your ohm meter should read APPROXIMATELY...
- 1.02K ohms in ice water
- 1.09K ohms at room temperature
- 1.36K ohms in boiling water.
If you get approximately these readings, then it is NOT the oven sensor. If that checks out then re-install the sensor AND the connector.

If it is NOT the sensor, replace the controller board.
- Take a moment to write down the color of the wire to the LETTERING (N, L, G, C / COM,,,) on the controller board. The connectors are in different locations on the new controller board so the wire color to the letter designation is significant.
- Carefully remove the wires one at a time
- VERY carefully remove the keypad ribbon cable from the right side of the controller board.
-- The ribbon cable will disconnect by releasing some little pressure clips on the side of the connector.
- Remove the controller board (4 screws)
- Install new controller board (4 screws)
- VERY carefully connect the keypad ribbon cable on the right side.
-- Make sure that the connector is in the OPEN position first, then,
-- Slide in the cable ensuring that all parts of the ribbon made it into the connector, then
-- Press down on the connector locking tabs.
- Reconnect each wire to the correctly lettering on the board.
-- Again, the connectors MAY BE in a different order on the replacement controller board. Match color to letter.
- Reconnect the (5 wire?) connector that includes the white oven sensor wires.
- Make sure everything looks normal, (i.e. no wires are pinched, remove tools from top of oven area, etc.)
- Re-install top cover.
- Re-install service connect cover.

You can test the unit while it is out of the cabinet,
- Make SURE that all sheet metal covers are in place.
- Flip power breaker to "On".
- Test that oven gets to the desired temp. Read more...

Videos!

Your Price

$209.05

General Electric Microwave Oven Combo Temperature Sensor Kit

★★★★★

8 Reviews

PartSelect Number PS236490

Manufacturer Part Number WB23X5340

This kit includes the sensor as well as the connectors. NOTE This sensor is 2" long.

Fixes these symptoms

Little to no heat when baking
Oven is too hot
Oven not heating evenly
See more...

Installation Instructions

CHARLA from NEW BRAUNFELS, TX

Oven sensor was not holding temperature range.

Per the instructions included with part. Read more...

Your Price

$27.97

General Electric Microwave Oven Combo SENSOR Assembly

PartSelect Number PS3486590

Manufacturer Part Number WB21T10018

Your Price

$101.35

General Electric Microwave Oven Combo Microwave Humidity Sensor

PartSelect Number PS1020486

Manufacturer Part Number WB27X10857

The humidity sensor detects humidity inside the microwave and communicates the temperature to the electronic control board.

Installation Instructions

Chris from Springfield, VA

Oven wouldn't sensor reheat & error code on display

I looked at the exploded pic on your web site to find the location of the sensor. Next I removed the cover by unscrewing 15 screws then swaped the sensor and re assembled! Works great! Fixing it my self I saved at least 150$ and did not have to wait all day for a repair man who probaly would not have the part on the first visit. Read more...